0
votes
0answers
19 views

HP 5800 VLAN Translation

I have a network of HP 5800. We route customers on different CVLANS but have them all within the same SVLAN. I have a PPPoE server that runs on 1 switch on VLAN 1500. Example: Site1: 1000:2 Site2: ...
2
votes
1answer
3k views

Configuring VLANs on HP 1910 switch

I understand how VLANs work, but am not quite sure what the various settings in my HP switch actually do. I have an HP 1910 switch, and I'm using the web interface to configure it (personally I'd ...
1
vote
1answer
265 views

HP Procurve 2610 vlan routing

Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all ...
5
votes
1answer
321 views

Tag/Untag VLANs from Port Perspective on HP Switch

I'm familiar with vlans and tagging, and we usually use the command line interface for our HP Layer 3 switches. I've done quite a few: vlan 10 untagged 21 I've always wondered if this was possible ...
1
vote
1answer
189 views

HP N40L / Intel 82574L VLAN Leakage

This is a follow on from a previous question (Switch sending DHCP packets to wrong VLAN) but the problem turns out that it's not with the switch, but more so in the NIC hardware I believe. Basically, ...
0
votes
1answer
469 views

Getting invalid input error on procurve 2510 when setting up ip helper-address

I have 3 HP Procurve 2510G-48 and I want to setup a VLAN for public wifi (VLAN100). Originally I just had the default vlan1. I have computers communicating across switches on VLAN100 with static IP ...
2
votes
1answer
4k views

InterVLAN routing on a HP V1910 series switch

Recently bought a HP V1910-16G switch (former 3com 29хх) with IPv4 routing capabilities. After unpacking I did a firmware upgrade to the latest 5.20 Release 1513P06. I did set up additional VLANs (#2 ...
5
votes
1answer
819 views

Procurve Primary VLAN

I'm trying to depreciate usage of VLAN 1 on my ProCurve switches; 1 is unused. I understand that VLAN 1 must exist, but I want to remove it from all ports, especially trunks between switches. The ...
1
vote
0answers
175 views

How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

As you can see from my question, I have a VLAN configuration problem with a ProCurve 3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I ...
1
vote
0answers
2k views

HP Procurve 2910AL allow traffic from VLAN to VLAN

We are trying to setup so that the switch handel routing and communication between a few vlans. And then have a link network up to the fw. Here is the config: Running configuration: ; J9145A ...
2
votes
2answers
3k views

VLAN security on HP ProCurve 1810G-24?

I'm looking into the managed switch HP ProCurve 1810G-24 to see if it can meet our office demands. The specs say it has IEEE802.1Q - whatever that means. Our office consists of four companies that ...
-2
votes
2answers
1k views

VLAN routing issue

I have HP Procurve Switch 2910AL-24G. Please see attached configuration. Client inst2is01 (10.247.167.80) and VLAN ID is 37 Server ILO (Management Port) IP : 10.247.172.70 and VLAn ID is 54 From ...
8
votes
3answers
2k views

HP Procurve Issue Passing Multiple VLANs over a link

Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2610 switch. This switch is then ...
1
vote
3answers
3k views

Cisco Catalyst VTP to HP ProCurve GARP?

I have two L3 capable ProCurve switches (2810-24G) which I would like to use in our Cisco environment. The Cisco switcheshave vtp configured, and all VLANs are added/maintained basically on the ...
0
votes
1answer
417 views

Procurve Switch Multiple Gateways

I have a Procurve 3500yl switch that is currently handling all of the VLANs and the default gateway for my network. Currently, the gateway is set to our old FreeBSD firewall/router and I am trying to ...
1
vote
1answer
2k views

Create a VLAN on HP Procurve switches

New to this site, but it's pretty darn great, so I won't be a stranger here! Still a n00b though :-) Need a walkthrough on howto create a VLAN. I have the ipadress space for the VLAN I have the ...
0
votes
1answer
747 views

Wireless guest access with HP ProCurve 420

We have a HP ProCurve 420 wireless access point hooked up to our LAN, which then connects to the internet though a gateway router. Is it possible to set up a guest SSID, which can access the internet ...
2
votes
1answer
10k views

Configuring VLAN's on two HP procurve switches

Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects ...