Group of hosts with a common set of requirements connected as if on the same broadcast domain despite physical location

learn more… | top users | synonyms

3
votes
0answers
89 views

Configuring Container with bridges and vlans (server only?)

I have two groups of lxc contianers on a server and want to isolate their network traffic for security reasons. I will be using port forwarding so the containers much each have separate IP's. I know I ...
2
votes
0answers
62 views

Debian does not shut down interface with ip link set … down

I have a really specific question for a trunk-testing environment. I have this network setup: +------------+ +------------+ | | +-----+ | | | eth0 ...
2
votes
0answers
68 views

Juniper SSG-5 different vlans authentication

In my network infrastructur I have 2 companies right now. Every company has it own vlan. For example: Company A 192.168.100.0/24 Company B 192.168.101.0/24 I want to use a shared vlan for all ...
2
votes
0answers
678 views

Configure vlan on Netgear switch via SNMP

I am trying to configure vlans on a netgear GS752TSX from the Linux command line with netsnmp. I have created vlan 99 on the web interface now want to control the pvid settings, egress and tagging. I ...
2
votes
0answers
2k views

Single Sign On 802.1x Wireless - saying “Connecting to <SSID>”, hangs for 10 seconds, fails with “Unable to connect to <SSID>, Logging on…”.

We are implementing WiFi on Windows 7 machines in our corporate environment. Machines should be able to log into the domain by WiFi as the Machine (Pre-Logon), and as the User (Post-Logon). We have ...
2
votes
0answers
136 views

dsl router for bridging two lans

I have two office locations that each have DSL service. I have the routers set up so that the two subnets, 10.0.1.x and 10.0.2.x, correctly keep data on each subnet and or pass across to the other ...
1
vote
0answers
32 views

Trunk vlans inside openvz container (Proxmox)

I have a node running OpenVZ CT (ProxMox). eth1 on HN are bridged through vmbr1 to veth device on CT101 (eth1 inside container). (Host Node) eth1 -> vmbr1 <- veth101.1 <- eth1 (CT101) No ...
1
vote
0answers
25 views

Windows Server spamming devices on other subnets on port 445

I have a Windows Server 2012 that every few seconds sends packets destined for port 445 on local IPs on other subnets. The IPs on other subnets it is trying to reach are devices such as VoIP phones, ...
1
vote
0answers
52 views

VLAN configuration on HP J9279A

I've tried to set up separate VLAN for lab environment on one of my HP switches (J9279A/J9280A). Network schema: WAN | GW | ...
1
vote
0answers
62 views

Can pvlan-trunk Ports Carry normal vlans too on Juniper EX8208?

I'm trying to implement pvlan on Juniper EX8208 which will span across multiple switches (to a Cisco nexus 7000 Series) and need to know if the Inter-Switch-Link Port with "pvlan-trunk" will allow ...
1
vote
0answers
51 views

How does Juniper vlan.0 work with policies?

I'm trying to understand vlan.0 and Juniper policies. Referring to here: http://kb.juniper.net/InfoCenter/index?page=content&id=KB16667 According to the link above, it seems that if I use ...
1
vote
0answers
102 views

Separate L2TP/IPsec VPNs with dynamic VLAN assignment

I am working on a Linux (Debian 7) VPN concentrator for different kinds of remote access. One of the offered protocols is L2TP/IPsec because of the client availability. I am using xl2tpd which in turn ...
1
vote
0answers
95 views

HP 5120 vlan not working

So I have this odd issue with our HP 5120 switches. The VLANs will not pass traffic unless a interface with a IP is assigned to the VLAN. Problem is there is a limit of 8 VLAN interfaces that are ...
1
vote
0answers
57 views

Inter VLAN Routing

I have VLAN 1 and VLAN 2 setup on HP ProCurve Switch, each linked to a different scope on DHCP server. VLAN1 = 10.220.0.0/23 VLAN2 = 10.210.0.0/21 I can't ping VLAN1 devices from VLAN2 and vice ...
1
vote
0answers
236 views

DRAYTEK - VLANs with VLAN tagging switches / router

Our company uses Draytek routers (various models, slowly upgrading to 2860n at each site). We have recently purchased a new site, and want to split the network up into separate VLANs, so as to ...
1
vote
0answers
106 views

Routing between L2 isolated ports

I am to deploy some managed switches for FTTB/FTTH and preparing configuration to introduce isolation between customers (by disabling L2 forwarding between client ports or using private VLANs). ...
1
vote
0answers
133 views

Guest wireless. HP to Cisco VLANs

I'm having trouble getting guest Internet access working. I have HP V-M200 WAPs and a Cisco RV042G for internet and a HP 1910 switch in the middle. I created a second Wireless Community/SSID on the ...
1
vote
0answers
127 views

Linux as gateway with VLANs failing for local network

We have a private VLAN being routed out from a host connected both to it and to our public network. Hosts on the private VLAN have the private IP address of the gateway host (10.2.2.82) set as their ...
1
vote
0answers
367 views

Cisco vlan entry missing in vlan.dat, but appears in running-config

One of our vlan's (ID: 104) stopped working suddenly and computers on that vlan failed when trying to obtain a dhcp ip address. On the Cisco switch if we do show vlan, this command is supposed to ...
1
vote
0answers
2k views

OpenWrt on TL-WR1043ND - VLAN to VLAN communication

I have this network configuration at home: 3G Wifi router - for access to internet, 192.168.1.0 subnet Router TP-Link TL-WR1043ND - OpenWRT (12.09), 192.168.2.0 subnet, connected wirelessly via ...
1
vote
0answers
583 views

debian KVM - network bonding fails with vlan and bridge

i have a Debian 6 system configured with 2 NICs these NICs are used on a bond (bond0) which is used by bridge that require to use VLAN. i can get connection between guests running on VLAN10 but it ...
1
vote
0answers
514 views

Ghost “vlan 0” tags added to ethernet frames in CentOS guest under OpenStack

I'm trying to debug an issue involving a KVM virtual machine instance where the instance doesn't respond to network requests when the source is on another physical machine, which is on the same subnet ...
1
vote
0answers
66 views

VLANS and Public/Private Traffic

I may reveal some ignorance with this question, but I am really confused. We have 3 static IPs and one gateway/modem with my organization. The gateway/modem is located in a remote area of our ...
1
vote
0answers
738 views

PFSense VLAN's - clients cant access devices on a defined VLAN

I'm having an issue setting up pfSense with VLAN's, basically, the pfSense boxes can ping the devices on the tagged vlan, but clients routing through pfSense cannot. There are two Cisco SG500 ...
1
vote
0answers
233 views

How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

As you can see from my question, I have a VLAN configuration problem with a ProCurve 3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I ...
1
vote
0answers
2k views

Is it possible to mix jumbo frames VLAN and standard mtu VLAN on the same switch port?

If a managed switch and all attached devices both support VLANs and Jumbo Frames, is it possible to mix VLANs with jumbo frames and VLANs with standard frames on the same switch port / ethernet card? ...
1
vote
0answers
545 views

Access All VLANS over XenServer Interface

For my current setup, I have a physical NIC on a XenServer machine that receives traffic tagged with various VLAN IDs. I have a virtual machine that is running Vyatta that needs to be able to access ...
1
vote
0answers
89 views

Datacenter redundant hosting setup advice

We are moving our servers to a new DC and I am looking for a bit of advice with our new COLO setup. I have some knowledge of networking but I am an enthusiast more than anything so it gets a bit ...
1
vote
0answers
4k views

HP Procurve 2910AL allow traffic from VLAN to VLAN

We are trying to setup so that the switch handel routing and communication between a few vlans. And then have a link network up to the fw. Here is the config: Running configuration: ; J9145A ...
1
vote
0answers
2k views

Cisco 891w multiple VLAN configuration

I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate ...
1
vote
0answers
582 views

Simple VLAN Trunking between 2 switches

I am trying to set up a connection between 2 buildings. In building 1 I have the following: Network 1 192.168.2.0/24 Network 2 192.168.3.0/24 Network 3 192.168.0.0/24 Network 4 ...
1
vote
0answers
165 views

Duplicate packets on network after disconnecting wireless access point on separate VLAN

We have a network with a few switches. One of these is a 3com 4500, where there are many computers connected, a custom linux firewall and a wireless bridge. The port where the wireless bridge and the ...
1
vote
0answers
217 views

Can multiple VLANs be provided with multicast addresses by a single MADCAP server?

Can a single DHCP server provide dynamic multicast addresses for hosts in many VLANs using MADCAP, just like it can provide hosts with unicast addresses via ip-helper? Or from a Cisco perspective, ...
1
vote
0answers
489 views

HP ProCurve & Cisco switches interoperability

I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below ...
1
vote
0answers
167 views

Network Segregation for IaaS/SaaS Environment

I've inherited a Dell M1000e blade chassis and 16 M600 blades that I'm now in the middle of migrating from standalone to clustered. Each is running Server 2008 R2 SP1 and Hyper-V. My issue is I'm ...
1
vote
0answers
516 views

Dell PowerConnect 6224F ACL Not Performing as Expected

What I'm trying to achieve is as follows: Allow full access to the device on 10.58.9.32 (our VoIP server), from anywhere on our network. Allow ICMP to flow in all directions to/from any device. ...
1
vote
0answers
877 views

Max STP instances reached on Cisco 2950 despite not actively using 64

I have a Cisco 5505 switch running CatOS connected to a number of Cisco 2950 switches running IOS. The 5505 switch supports a large number of vlans (I'm guessing 1005), yet the 2950s only support a ...
0
votes
0answers
14 views

Sharing a WAN connection between 3 companies

I have been asked to install a network to share a BT fibre connection between three unrelated companies. The WAN is presented on a cisco 2900 series router (managed by the ISP) with a gateway address ...
0
votes
0answers
22 views

How to setup 2 switch with VLAN and 2 IPs for each in different block

Below I have depicted the required network. In this network: Lets say GW1 is in IP1 block and GW2 is in IP2 block. There are 2 Linux running PCs with 4 NICs. 1st Linux PC is connected to 2 GWs with ...
0
votes
0answers
12 views

Deny DHCP-Requests for specific subnets on specific interfaces

I have a router (Ubuntu 14.04) running the isc-dhcpd-server on the interfaces em2.X (X can be any of the VLANs 2, 3, 4). Each interface has its own 192.168.X.0/24 subnet. Now I have a Windows-Client ...
0
votes
0answers
57 views

Bridge on vlan on teaming for KVM

I have problem to create bridge on vlan on teaming. Why I do something like that? - Kvm needs bridge - Vlans because I need vm’s in different subnets - Teaming in option active-backup (small HA) I do ...
0
votes
0answers
14 views

VLAN on access port between Dell6248 and 5548

I have a Dell 6248 which is connected to firewall through Dell 5548 6248 (g23)-----(g48)5448(g43)----(x0)sonicwall Below is the vlan config of 6248 interface vlan 4 name "Four" routing ip address ...
0
votes
0answers
25 views

pfsense routing with dmz wan and sonic wall

Pfsense setup: 2 physical NIC's (1 input from modem/ISP, 1 LAN with a lot of vlans and DMZ) Network setup: WAN block from ISP xxx.xxx.xxx.225/28 Modem -> pfsense -> vlan 40 (192.168.40.0/24) ...
0
votes
0answers
26 views

ARP/ICMP in a network environment with overlapping IP address

Currently I have lab network setup to mimic customer's network deployment. (According to the customer, they are using VRF over VLAN so that their customer can have overlapping network connecting to ...
0
votes
0answers
22 views

Watchguard VLAN Head-Grasping needed

I am trying to wrap my head around setting up my new watchguard M400. Here's what I need to figure out and what I've done so far. My ISP provided me with a P2P IP, which I plugged into my interface ...
0
votes
0answers
52 views

Draytek Vigor 2860 multiple external IP-addresses

I've bought a DrayTek Vigor 2860 for my company network. And I'd like to use it for two VLANs with separated external IP's. I have 6 LAN ports on my DrayTek. For example: External IP-adres: ...
0
votes
0answers
36 views

Vlan trunk between three switches and KVM Guests

I'am trying to find information regarding the appropriate configuration between three switches and KVM. More depth as per diagram. I need to create a tunnel for traffic created on sw1-port5 to be ...
0
votes
0answers
23 views

ebtables captive portal bridge vlan

http://s16.postimg.org/e5nu6g1md/bridgevlancaptive.png Attached link image is based on my project about captive portal. As you can see on the image i have diagram on LEFT side which is WORKING ...
0
votes
0answers
60 views

Layer 3 switch redundancy solution (with vlan's, stp)

So basicly I have a setup which I want to get to work but i'm unable to. It's possible I am overseeing a lot of things but let's get to it anyways. The current situation is a network with 4 switches ...
0
votes
0answers
31 views

HP IP Routing Topology

We have 1 main HP Switch in Server Room and 6 other data closets switches that connect the clients. In terms of routing we have 3 VLANs that require routing. Right now the only switch that does any ...