-2
votes
1answer
76 views

Easiest routing solution for a typical firewall with WiFi routers setup - WAN-2-hops-away network

Suppose a local network connected to the internet via a single firewall router. Devices that connect directly (= using only layer 2 devices) to that router are: hosts WiFi routers providing the ...
1
vote
0answers
65 views

Wireless Bridging two Sonicwall Firewalls

We have two sites (essentially two small buildings side by side but we are unable to run CAT5 cable between them) which are currently linked via a wireless bridge. We will be splitting the sites so ...
-1
votes
1answer
136 views

Correct antenna types for 802.11g wifi point to point network link [closed]

I maintain a work network that at one point bridges a gap between two buildings wirelessly, while also descending from the 4th floor to ground level. The AP is at the top and connects to the internet ...
1
vote
1answer
78 views

Would appreciate a routing configuration advice

I have a problem with a host visibility which I think is caused by incomplete network configuration. There is an ADSL-router which has a DMZ subnet 192.168.0/24. In this network there is a wireless ...
1
vote
1answer
749 views

What are the security risks in running pfsense on a box with a wireless radio?

In my network pfsense is the firewall and router for my entire network. It is the only machine with direct WAN access. All other machines are behind it (and connected through a switch). I am trying to ...
1
vote
0answers
115 views

AP Clients not pingable from outside

Here's a rough scheme of my network: - http://i.stack.imgur.com/zrlJJ.png The network is divided into VLANs. The linksys device is connected to a VLAN20 access port. Clients 4, 3, 2 ping the rest of ...
2
votes
1answer
147 views

Selective Routing Between Subnets

I have a configuration with two subnets. For this example I will call them 192.168.1.128/26 (128) and 192.168.1.64/26 (64). The 64 subnet contains all the internal devices that guests should not be ...
1
vote
2answers
2k views

Jumbo frames with wireless client

I currently have the following network configuration Apple Time Capsule (Gigabit Ethernet router) 2 Windows desktop wired with Gigabit ethernet 1 MacBook Pro in wireless N mode 1 iPhone (obviously ...
0
votes
2answers
496 views

Can't ping wireless laptop from internal network

If I connect a laptop wirelessly to my router it gets assigned an IP of 192.168.4.X. If I use a wired computer inside the same network (IP:192.168.2.X) I am not able to ping the laptop, but I am able ...
2
votes
2answers
2k views

Using Ubuntu 10.04 as access point

Is there an easy way to configure Ubuntu laptop as access point? Sometimes when I only have cable connection to the internet I would like to give my gadgets access to the internet using WiFi. Is it ...
0
votes
1answer
368 views

Routing DHCP through a wireless router

I have a SBS 2003 server that is running DNS/AD/DHCP. Address space is 192.168.1.1. We added a new wireless router to the network to replace a old damaged Watchguard Firewall/gateway. Everything ...
0
votes
1answer
221 views

Dual NIC internet access

Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on. Not sure how the routes table would look like. Q2. If one of the NICs ...
1
vote
3answers
909 views

looking for wifi router with restricted access to LAN

I need to set up a separate Wifi network for guests, and am looking for a decent router which can be part of the LAN but restrict access so that it can only route to the gateway/WLAN. Are there any ...
0
votes
1answer
802 views

Setting up an Access Point with a WiMax USB Stick

I'm giving WiMax a try (Clear Wireless in Portland, if that matters). I opted for the USB stick because I'd like to be able to use it on the go. However, when I'm in my apartment I'd prefer to ...
2
votes
5answers
189 views

Wireless Router

Is it possible to connect 60 user to internet using wireless router while having 3MB ADSL Line. What the speed of internet the user will receive ? if yes which router (Model ) will support this ...
0
votes
1answer
3k views

Windows Server 2008 Routing / NAT - USB Wireless adapter not showing up

I have a multihomed system running Windows 2008 Server Enterprise, and I'm trying to share an Internet connection on a USB wifi adapter with the other networks attached to the system. To that end, I ...