The tag has no wiki summary.

learn more… | top users | synonyms

1
vote
0answers
102 views

Exclude an IP address from an openwrt firewall rule

I am using a wrt54gl with openwrt to try and redirect all traffic on my LAN to a specific server, which will run scapy and other network analysis tools and act as a gateway/firewall to the Internet. ...
0
votes
1answer
355 views

DD-WRT routers and subnets - how to get devices on same subnet to see each other?

We have an entry point from our ISP. It has the subnet 0, it's a MikroTik device over which we have zero control. We have 2 dumb 4-port switches and 2 wrt54gl routers with DD-WRT installed. These ...
1
vote
1answer
1k views

Router: WRT54GL vs. Raspberry Pi [closed]

For routing and firewalling between 4 L2 networks, I currently use a WRT54GL (without using the WIFI). There are 4 networks routed which come in by VLAN from a managed switch, so a only a single ...
0
votes
0answers
559 views

Switching from BT Router to Tomato - How to route an external IP block without using 1:1 NAT?

I've been struggling with an issue here at my office for at least a couple of days, and I've tried googling to no avail. I'm admittedly more of a coder than a network guy, so please bear with me! ...
14
votes
3answers
2k views

Slowest wireless client dictates the connection quality of all others?

Not sure if this is the place to ask this, but I couldn't find a more appropriate StackExchange site. I heard that the quality of wireless connection follows the law of the lowest common denominator - ...
5
votes
4answers
648 views

Radius feedback from AP to WiFi client

We have the following setup at our company: a gateway PC with CentOS (gw), running Radius and some traffic filtering programs. All of our employees connect wirelessly, and we have a WPA2 Enterprise ...
0
votes
1answer
674 views

Increase bandwidth of Linksys WRT54GL (with Tomato inside)

I have Linksys WRT54GL with Tomato firmware installed. When I connect internet cable directly to a computer I can download at about 8 MB/s, however when internet is access through the router maximum ...
0
votes
1answer
743 views

vpn connection fails with 800 code after wifi router reset

I previously had successfully set up a VPN connection that allowed my computer (Windows 7 Professional) to connect to a remote server. Last week, we had to reset our Lynksys WRT54GL wireless router, ...
1
vote
2answers
1k views

configure pppoe on wrt54gl(openwrt)

I have home DSL connection from my ISP with a beetel modem at my end. I want to make my network wireless, so i bought a linksys wrt54gl and installed open-wrt on it. My ISP provides dynamic IP's with ...
1
vote
3answers
682 views

wrt54gl reboots; troubleshooting steps?

I am using about 10 wrt54gl's in a small school. I am using a combination of stock firmware and Tomato 1.25, slowly moving towards all Tomato. We have had these devices installed for several years ...
0
votes
4answers
290 views

Linksys WRT54GL - Did we get a lemon? [closed]

I've been having problems with a Linksys WRT54GL router, with latest Linksys firmware. I've read a LOT of great reviews on this model but we are having instability problems with the network. Should ...
2
votes
4answers
5k views

Dual WAN port on a WRT54GL

Is it possible to reconfigure one of the LAN ports on a WRT54GL (running Tomato firmware) to act as a second WAN port? I have the following networks: PPOE connection to ADSL modem (works fine on ...
6
votes
1answer
3k views

Tomato firmware - View port 80 traffic

I'm using a WRT54GL router and i've installed the tomato firmware. Is there any shell command or somehting i can use to view all port 80 traffic? I want to se which internal ip has a connection to an ...