430 reputation
312
bio website 2130706433
location California
age 34
visits member for 4 years, 8 months
seen Apr 13 at 19:38
while(1)
{
    share(knowledge);
}

Jan
30
comment SSH Error: unknown key type '-----BEGIN'
@HaukeLaging, actually yes you can, but it depends on the key type. If it's a PKCS#8 key, you are correct. But if it's a PKCS#1 key or a DSA key, you'll see something like -----BEGIN DSA PRIVATE KEY----- Proc-Type: 4,ENCRYPTED DEK-Info: DES-EDE3-CBC,0000000000000000 before the base64 which is the giveaway. Also, if the PKCS#8 key is encrypted, the PEM header should say -----BEGIN ENCRYPTED PRIVATE KEY----- rather than just -----BEGIN PRIVATE KEY-----.
Jan
23
comment SSH Error: unknown key type '-----BEGIN'
After the BEGIN RSA PRIVATE KEY line, do the next few lines indicate that the key is encrypted, or is it just a block of base64?
Jan
23
awarded  Yearling
Jan
23
comment How to undo rm -rf?
Could try something like this... no guarantees though. Keep good backups.
Jan
22
revised Why can't I have the same subnet on WAN and LAN?
Remove flamebait at the top of the post.
Jan
22
suggested suggested edit on Why can't I have the same subnet on WAN and LAN?
Jan
22
answered Why can't I have the same subnet on WAN and LAN?
Jan
19
answered Is FTP and SFTP connection same
Jan
15
comment site to site vpn between sonicwall and pfsense
Not sure, but if you have completed phase 2 the tunnel should be up. Looks like it stays up for a little over 30 seconds, then dead peer detection shuts it down. What are your DPD timeouts set to? Do you have traffic going over the tunnel? Have you tried capturing packets while establishing the tunnel and then pushing traffic? Can you paste logs from the same time period so we can match up what happens on either side?
Nov
2
comment HP Procurve 2610 intervlan routing
@KenWhite I voted to close as off topic. I thought it may get automatically migrated, but I may be behind the times on that. On second thought though, it might be better to just close it without migration - there is not enough information to really answer the question as-is. I only posted an answer because I had a theory that seemed like a reasonable answer that was too long to post in the comments; really the question should have 2-3x the amount of details to make a good question on another site.
Nov
2
comment HP Procurve 2610 intervlan routing
@KenWhite, the accepted answer says it's OK to answer questions you think will be migrated. ;-)
Nov
2
comment HP Procurve 2610 intervlan routing
@KenWhite, point taken. I didn't realize this was controversial; I figured if the question was migrated, it could still be helpful at the destination site.
Nov
2
comment HP Procurve 2610 intervlan routing
No, I can't transfer it. I don't have the appropriate privilege level. Can you post a route table from one of the machines on VLAN 4 that cannot access the other VLANs?
Nov
2
answered HP Procurve 2610 intervlan routing
Nov
2
comment HP Procurve 2610 intervlan routing
Welcome to Stack Overflow. Unfortunately, this question is off topic for Stack Overflow. Server Fault might be a better site for this. But you'll need to be more specific about your question if you'd like an answer (there as well). For example, what troubleshooting steps have you tried? Can you ping the switch at 10.10.1.1 using a device off port 25 configured with a static IP address? Is there a DHCP server on that subnet? How are the hosts configured? If you don't get ping replies, do you see arp entries? What exactly do you mean by "inter vlan routing" not working?
Nov
1
comment How to specify proxy server big ip f5?
I think that's two different concepts. You're talking about setting up a reverse proxy, but then you're asking how to set up a forward proxy. If you're talking about HTTP replies in responses to requests that clients sent, those will already be flowing through the reverse proxy, since the reverse proxy opens a TCP session to the back-end server. What other traffic types do you need to go through the proxy?
Nov
1
comment Simple, centralized user management on a small LAN - NIS or LDAP?
It does look better supported on RHEL/CentOS. When setting up something as critical as an identity management service, it might be advisable to use the best-supported distribution, regardless of what the client machines are using, IMHO.
Jul
31
awarded  Citizen Patrol
May
14
awarded  Caucus
Apr
19
answered Attempting to allow SFTP connection to a preconfigured Linode