Reputation
7,978
Top tag
Next privilege 10,000 Rep.
Access moderator tools
Badges
14 29
Newest
 Caucus
Impact
~539k people reached

May
13
comment Juniper SRX210 routing vlans
If you need these three VLANs to be separated from each other, then you would places them into separate security zones. You may also have to adjust outbound NAT, not sure how the default config works anymore.
Nov
3
comment 2x uplinks in HSRP - how to setup switch?
Exactly what I intended to right once my comment was answered :)
Nov
1
comment 2x uplinks in HSRP - how to setup switch?
Do you have a router?
Oct
9
comment Dell 6248 Stacking - Cross Connect Does not work
Hard to say... you're using the SFP ports and transceivers? Are you sure your SFP transceivers and the cable you are using are all the same kind? ie... SFP Copper transceivers with Cat5e/6 in between or SFP+ 10Gb multi-mode fiber modules with multi-mode fiber cables in between? Past that, its proper configuration. Are you using VLANs?
Oct
8
comment Slow local area network speeds
I second checking the physical switch flow control and speed/duplex settings.
Oct
2
comment Is it realistic to host ESXi on a cloud VPS?
You'd be surprised how many of VMware's own labs are running inside nested ESXi environments... its a valid question!
Sep
25
comment Need advice on Juniper OSPF networking
I am fairly certain to get back to a packet based mode where you can use an SRX as a router requires a bunch of downgrades to 9.X code which might be a big headache at this point. I would set the default policy to permit, and then put all interfaces in the same zone. You would still need to set host-inbound-traffic for the zone to permit all as well.
Sep
25
comment Need advice on Juniper OSPF networking
This is an SRX, you nuked the entire security section. You need to permit "host-inbound-traffic" meaning traffic meant for the routing engine for OSPF packets to exchange between other peers. Further, you need a security zone assigned to these and rules to permit traffic to flow. What version of JunOS?
Sep
2
comment Troubleshooting blocked/dropped ports on Sonicwall firewalls
What version of SonicOS? There are built-in graphs and reporting to show this.
Aug
22
comment Can we install one printer that prints to different printers depending on which location/office an employee is in?
Use the same IP subnet at each site, and give the printers the same address. You'll be stuck in driver hell though.
Aug
19
comment Inter-VLAN Malicious Code Scanning
Exactly how many ports are we talking? You can use a span port to monitor some traffic. Why not use a single port and VLAN tagging? I'm not sure how many monitor sessions a 3750 can support. You could also use ESXi to run the hosts and let it forward netflow to a collector.
Aug
14
comment Why would a raid 1 “break” on it's own?
What type of hardware, software or hardware RAID?
Aug
14
comment Is it possible to transfer an IP address from one host to another?
And clarify what is moving, the nameserver or the webhost.
Aug
14
comment Is it possible to transfer an IP address from one host to another?
Changing 600 DNS records would take about 0.9 seconds using a script and then the time it takes for TTL and name servers to update. Why is this unacceptable?
Jul
8
comment Domain Controller DCdiag error - A Global Catalog Server could not be located
Seems like the tune on how best to do this changes, again, and again, and again.
Jun
10
comment ESXi boot time with 9 iSCSI targets
Interesting, what kind of SAN was this?
May
11
comment Monitor bandwidth usage of a datacenter
Two downvotes 3 years later? Really? :D
May
8
comment Intermittent 100% CPU on all VMs
Is perfmon showing any disk queuing? Do you the OpenManage packages installed?
Apr
7
comment Where is the documentation for mixing DFS-R between Windows 2012 and Windows 2012 R2?
better! hopefully someone from experience can chime in, I was not able to find anything on my first google-fu pass, good luck.
Apr
6
comment Where is the documentation for mixing DFS-R between Windows 2012 and Windows 2012 R2?
This is totally a "what does the documentation say" question.