2

I'm using following:

# cat /etc/redhat-release 
CentOS Linux release 7.1.1503 (Core) 
# rpm -q firewalld
firewalld-0.3.9-11.el7.noarch
#

I'm trying to block specific IP address (10.52.208.220) from reaching it from my system, yet unable to do so:

before:

# firewall-cmd --reload
success
# firewall-cmd --list-all
public (default, active)
  interfaces: eno1
  sources: 
  services: dhcpv6-client high-availability http https ssh
  ports: 5666/tcp 3306/tcp 5900/tcp 9001/tcp
  masquerade: no
  forward-ports: 
  icmp-blocks: 
  rich rules: 

# ping -c1 wcmisdlin01
PING wcmisdlin01.uftmasterad.org (10.52.208.220) 56(84) bytes of data.
64 bytes from wcmisdlin01.uftmasterad.org (10.52.208.220): icmp_seq=1 ttl=64 time=0.379 ms

--- wcmisdlin01.uftmasterad.org ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.379/0.379/0.379/0.000 ms
#

after:

# firewall-cmd --add-rich-rule='rule family="ipv4" destination address="10.52.208.220" protocol value="icmp" reject'
success
# firewall-cmd --list-all
public (default, active)
  interfaces: eno1
  sources: 
  services: dhcpv6-client high-availability http https ssh
  ports: 5666/tcp 3306/tcp 5900/tcp 9001/tcp
  masquerade: no
  forward-ports: 
  icmp-blocks: 
  rich rules: 
    rule family="ipv4" destination address="10.52.208.220" protocol value="icmp" reject

# ping -c1 wcmisdlin01
PING wcmisdlin01.uftmasterad.org (10.52.208.220) 56(84) bytes of data.
64 bytes from wcmisdlin01.uftmasterad.org (10.52.208.220): icmp_seq=1 ttl=64 time=0.266 ms

--- wcmisdlin01.uftmasterad.org ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.266/0.266/0.266/0.000 ms
# 

IPTABLES(8) - iptables/ip6tables — administration tool for IPv4/IPv6 packet filtering and NAT

# iptables --list IN_public_deny
Chain IN_public_deny (1 references)
target     prot opt source               destination         
REJECT     icmp --  anywhere             wcmisdlin01.uftmasterad.org  ctstate NEW reject-with icmp-port-unreachable
# 

What am I doing wrong?

2
  • IN_public_deny sounds like it is for inbound packets, e.g. from the remote system to your system. This would therefore not block a outgoing connection from your system to the host in question, as the response from the blocked host would be shuffled through the connection state created by the outgoing packet.
    – thrig
    Aug 27, 2015 at 15:33
  • @thrig that's what I thought too, that's why I included in my question, but then again chain can be named differently, the question is how to make it work)
    – alexus
    Aug 27, 2015 at 15:35

1 Answer 1

0

On inspection of the full iptables -n --list output, IN_public_deny is (eventually) called from the INPUT chain, which has nothing to do with packets sent from the system to the thus undenied host; those packets are instead routed through the OUTPUT chain (or possibly FORWARD if the firewall is a router or bridge between the source and destination). firewalld.richlanguage(5) does not appear to offer any means of specifying that the rule must go onto the OUTPUT (or FORWARD) chain, so the "last resort" option of a direct rule appears to be one solution.

firewall-cmd --direct --add-rule ipv4 filter OUTPUT_direct 0 -p icmp -d 10.52.208.220 -j REJECT --reject-with icmp-host-prohibited

(Though usually I prefer to DROP (and possibly LOG with rate limiting) instead of sending ICMP rejects, as if the host-to-be-blocked is going nuts, throwing ICMP response packets to it back onto a burdened network can make things go from bad to worse...)

0

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .