What is the easiest way to setup max login attempts in a LAMP environment (sshd installed via yum)? Is there a package or simple firewall rule?
I use Fail2ban; I've used Denyhosts in the past, and it works quite well, too. I favor Fail2ban now because it is more configurable, and more able to handle monitoring multiple different services -- for example, your sshd and you web app's login page simultaneously (provided you log failures).
Another method you might consider is implementing a LIMIT rule in
iptables; I unfortunately can't help you with this, unless you want to install Shorewall, and then I'd simply point you toward the excellent documentation on that site for how to configure a LIMIT rule to, well, limit the ability of someone to brute-force your server.
I don't like to use any third party tools. Hence I used a combination of ssh configuration and firewall settings. With the following solution an attacker is allowed to produce exactly 3 fault logins in 2 minutes, or he will be blocked for 120 seconds.
1) Add the following line to
This will allow only 1 login attempt per connection. Restart the ssh server.
2) Add the following firewall rules
Create a new chain
iptables -N SSHATTACK iptables -A SSHATTACK -j LOG --log-prefix "Possible SSH attack! " --log-level 7 iptables -A SSHATTACK -j DROP
Block each IP address for 120 seconds which establishes more than three connections within 120 seconds. In case of the fourth connection attempt, the request gets delegated to the
SSHATTACK chain, which is responsible for logging the possible ssh attack and finally drops the request.
iptables -A INPUT -i eth0 -p tcp -m state --dport 22 --state NEW -m recent --set iptables -A INPUT -i eth0 -p tcp -m state --dport 22 --state NEW -m recent --update --seconds 120 --hitcount 4 -j SSHATTACK
3) See log entries of possible ssh attacks in
Dec 27 18:01:58 ubuntu kernel: [ 510.007570] Possible SSH attack! IN=eth0 OUT= MAC=01:2c:18:47:43:2d:10:c0:31:4d:11:ac:f8:01 SRC=192.168.203.129 DST=192.168.203.128 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=30948 DF PROTO=TCP SPT=53272 DPT=1785 WINDOW=14600 RES=0x00 SYN URGP=0
There's not a specific package associated with SSH to set this up. You could however install CSF which is ConfigServer & Firewall.
Two Configuration changes I'd suggest would be made in the file: /etc/ssh/sshd_config
Limit the maximum number of unauthenticated connections that the ssh server will handle at the same time. The smaller this is, the harder it is for script kiddies to make parallel, coordinated cracking attempts with multiple connections. edit sshd_config and change MaxStartups from the default of "10" to "3:50:10". The colon separated values tells the ssh server to, "allow 3 users to attempt logging in at the same time, and to randomly and increasingly drop connection attempts between 3 and the maximum of 10". Note: this should be increased on servers with substantial numbers of valid ssh users logging in.
- Default: MaxStartups 10
- MaxStartups 3:50:10
Reduce the maximum amount of time allowed to successfully login before disconnecting. The default of 2 minutes is too much time to hold open an unauthenticated connection attempt (see above); 30 seconds is more than enough time to log in:
- Default: LoginGraceTime 2m
- LoginGraceTime 30
I use these IPTables rules for this:
iptables -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --set --name SSH -j ACCEPT iptables -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --update --seconds 300 --hitcount 4 --rttl --name SSH -j DROP
That will only allow 4 TCP/SYN packets to port 22 from an IP address in 5 minutes. If it makes more attempts the door is closed till 5 minutes are over.
there is an option that you can put into your sshd_config file for the server:
MaxAuthTries Specifies the maximum number of authentication attempts permitted per connection. Once the number of failures reaches half this value, additional failures are logged. The default is 6.