I have several TBs of very valuable personal data in a zpool which I can not access due to data corruption. The pool was originally set up back in 2009 or so on a FreeBSD 7.2 system running inside a VMWare virtual machine on top of a Ubuntu 8.04 system. The FreeBSD VM is still available and running fine, only the host OS has now changed to Debian 6. The hard drives are made accessible to the guest VM by means of VMWare generic SCSI devices, 12 in total.

There are 2 pools:

  • zpool01: 2x 4x 500GB
  • zpool02: 1x 4x 160GB

The one that works is empty, the broken one holds all the important data:

[user@host~]$ uname -a
FreeBSD host.domain 7.2-RELEASE FreeBSD 7.2-RELEASE #0: \
  Fri May  1 07:18:07 UTC 2009                          \
  root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC  amd64

[user@host ~]$ dmesg | grep ZFS
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
ZFS filesystem version 6
ZFS storage pool version 6

[user@host ~]$ sudo zpool status
  pool: zpool01
 state: UNAVAIL
 scrub: none requested

    zpool01     UNAVAIL      0     0     0  insufficient replicas
      raidz1    UNAVAIL      0     0     0  corrupted data
        da5     ONLINE       0     0     0
        da6     ONLINE       0     0     0
        da7     ONLINE       0     0     0
        da8     ONLINE       0     0     0
      raidz1    ONLINE       0     0     0
        da1     ONLINE       0     0     0
        da2     ONLINE       0     0     0
        da3     ONLINE       0     0     0
        da4     ONLINE       0     0     0

  pool: zpool02
 state: ONLINE
 scrub: none requested

    zpool02     ONLINE       0     0     0
      raidz1    ONLINE       0     0     0
        da9     ONLINE       0     0     0
        da10    ONLINE       0     0     0
        da11    ONLINE       0     0     0
        da12    ONLINE       0     0     0

errors: No known data errors

I was able to access the pool a couple of weeks ago. Since then, I had to replace pretty much all of the hardware of the host machine and install several host operating systems.

My suspicion is that one of these OS installations wrote a bootloader (or whatever) to one (the first ?) of the 500GB drives and destroyed some zpool metadata (or whatever) - 'or whatever' meaning that this is just a very vague idea and that subject is not exactly my strong side...

There is plenty of websites, blogs, mailing lists, etc. about ZFS. I post this question here in the hope that it helps me gather enough information for a sane, structured, controlled, informed, knowledgeable approach to get my data back - and hopefully help someone else out there in the same situation.

The first search result when googling for 'zfs recover' is the ZFS Troubleshooting and Data Recovery chapter from Solaris ZFS Administration Guide. In the first ZFS Failure Modes section, it says in the 'Corrupted ZFS Data' paragraph:

Data corruption is always permanent and requires special consideration during repair. Even if the underlying devices are repaired or replaced, the original data is lost forever.

Somewhat disheartening.

However, the second google search result is Max Bruning's weblog and in there, I read

Recently, I was sent an email from someone who had 15 years of video and music stored in a 10TB ZFS pool that, after a power failure, became defective. He unfortunately did not have a backup. He was using ZFS version 6 on FreeBSD 7 [...] After spending about 1 week examining the data on the disk, I was able to restore basically all of it.


As for ZFS losing your data, I doubt it. I suspect your data is there, but you need to find the right way to get at it.

(that sounds so much more like something I wanna hear...)

First step: What exactly is the problem ?

How can I diagnose why exactly the zpool is reported as corrupted ? I see there is zdb which doesn't seem to be officially documented by Sun or Oracle anywhere on the web. From its man page:

       zdb - ZFS debugger

       zdb pool

       The  zdb  command is used by support engineers to diagnose failures and
       gather statistics. Since the ZFS file system is  always  consistent  on
       disk  and is self-repairing, zdb should only be run under the direction
       by a support engineer.

       If no arguments are specified, zdb, performs basic  consistency  checks
       on  the pool and associated datasets, and report any problems detected.

       Any options supported by this command are internal to Sun  and  subject
       to change at any time.

Further, Ben Rockwood has posted a detailed article and there is a video of Max Bruning talking about it (and mdb) at the Open Solaris Developer Conference in Prague on June 28, 2008.

Running zdb as root on the broken zpool gives the following output:

[user@host ~]$ sudo zdb zpool01
zdb: can't open zpool01: Invalid argument

I suppose the 'invalid argument' error at the end occurs because the zpool01 does not actually exist: It doesn't occur on the working zpool02, but there doesn't seem to be any further output either...

OK, at this stage, it is probably better to post this before the article gets too long.

Maybe someone can give me some advice on how to move forward from here and while I'm waiting for a response, I'll watch the video, go through the details of the zdb output above, read Bens article and try to figure out what's what...


Update 01:

I think I have found the root cause: Max Bruning was kind enough to respond to an email of mine very quickly, asking for the output of zdb -lll. On any of the 4 hard drives in the 'good' raidz1 half of the pool, the output is similar to what I posted above. However, on the first 3 of the 4 drives in the 'broken' half, zdb reports failed to unpack label for label 2 and 3. The fourth drive in the pool seems OK, zdb shows all labels.

Googling that error message brings up this post. From the first response to that post:

With ZFS, that are 4 identical labels on each physical vdev, in this case a single hard drive. L0/L1 at the start of the vdev, and L2/L3 at the end of the vdev.

All 8 drives in the pool are of the same model, Seagate Barracuda 500GB. However, I do remember I started the pool with 4 drives, then one of them died and was replaced under warranty by Seagate. Later on, I added another 4 drives. For that reason, the drive and firmware identifiers are different:

[user@host ~]$ dmesg | egrep '^da.*?: <'
da0:  <VMware, VMware Virtual S 1.0> Fixed Direct Access SCSI-2 device 
da1:  <ATA ST3500418AS CC37> Fixed Direct Access SCSI-5 device 
da2:  <ATA ST3500418AS CC37> Fixed Direct Access SCSI-5 device 
da3:  <ATA ST3500418AS CC37> Fixed Direct Access SCSI-5 device 
da4:  <ATA ST3500418AS CC37> Fixed Direct Access SCSI-5 device 
da5:  <ATA ST3500320AS SD15> Fixed Direct Access SCSI-5 device 
da6:  <ATA ST3500320AS SD15> Fixed Direct Access SCSI-5 device 
da7:  <ATA ST3500320AS SD15> Fixed Direct Access SCSI-5 device 
da8:  <ATA ST3500418AS CC35> Fixed Direct Access SCSI-5 device 
da9:  <ATA SAMSUNG HM160JC AP10> Fixed Direct Access SCSI-5 device 
da10: <ATA SAMSUNG HM160JC AP10> Fixed Direct Access SCSI-5 device 
da11: <ATA SAMSUNG HM160JC AP10> Fixed Direct Access SCSI-5 device 
da12: <ATA SAMSUNG HM160JC AP10> Fixed Direct Access SCSI-5 device 

I do remember though that all drives had the same size. Looking at the drives now, it shows that the size has changed for three of them, they have shrunk by 2 MB:

[user@host ~]$ dmesg | egrep '^da.*?: .*?MB '
da0:   10240MB (20971520  512 byte sectors: 255H 63S/T 1305C)
da1:  476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da2:  476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da3:  476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da4:  476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da5:  476938MB (976771055 512 byte sectors: 255H 63S/T 60801C) <--
da6:  476938MB (976771055 512 byte sectors: 255H 63S/T 60801C) <--
da7:  476938MB (976771055 512 byte sectors: 255H 63S/T 60801C) <--
da8:  476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da9:  152627MB (312581808 512 byte sectors: 255H 63S/T 19457C)
da10: 152627MB (312581808 512 byte sectors: 255H 63S/T 19457C)
da11: 152627MB (312581808 512 byte sectors: 255H 63S/T 19457C)
da12: 152627MB (312581808 512 byte sectors: 255H 63S/T 19457C)

So by the looks of it, it was not one of the OS installations that 'wrote a bootloader to one the drives' (as I had assumed before), it was actually the new motherboard (an ASUS P8P67 LE) creating a 2 MB host protected area at the end of three of the drives which messed up my ZFS metadata.

Why did it not create an HPA on all drives ? I believe this is because the HPA creation is only done on older drives with a bug that was fixed later on by a Seagate hard drive BIOS update: When this entire incident began a couple of weeks ago, I ran Seagate's SeaTools to check if there is anything physically wrong with the drives (still on the old hardware) and I got a message telling me that some of my drives need a BIOS update. As I am now trying to reproduce the exact details of that message and the link to the firmware update download, it seems that since the motherboard created the HPA, both SeaTools DOS versions to fail to detect the harddrives in question - a quick invalid partition or something similar flashes by when they start, that's it. Ironically, they do find a set of Samsung drives, though.

(I've skipped on the painful, time-consuming and ultimately fruitless details of screwing around in a FreeDOS shell on a non-networked system.) In the end, I installed Windows 7 on a separate machine in order to run the SeaTools Windows version Just a last remark about DOS SeaTools: Don't bother trying to boot them standalone - instead, invest a couple of minutes and make a bootable USB stick with the awesome Ultimate Boot CD - which apart from DOS SeaTools also gets you many many other really useful tools.

When started, SeaTools for Windows bring up this dialog:

SeaTools Firmware Update Dialog

The links lead to the Serial Number Checker (which for some reason is protected by a captcha - mine was 'Invasive users') and a knowledge base article about the firmware update. There's probably further links specific to the hard drive model and some downloads and what not, but I won't follow that path for the moment:

I won't rush into updating the firmware of three drives at a time that have truncated partitions and are part of a broken storage pool. That's asking for trouble. For starters, the firmware update most likely can not be undone - and that might irrevocably ruin my chances to get my data back.

Therefore, the very first thing I'm going to do next is image the drives and work with the copies, so there's an original to go back to if anything goes wrong. This might introduce an additional complexity, as ZFS will probably notice that drives were swapped (by means of the drive serial number or yet another UUID or whatever), even though it's bit-exact dd copies onto the same hard drive model. Moreover, the zpool is not even live. Boy, this might get tricky.

The other option however would be to work with the originals and keep the mirrored drives as backup, but then I'll probably run into above complexity when something went wrong with the originals. Naa, not good.

In order to clear out the three hard drives that will serve as imaged replacements for the three drives with the buggy BIOS in the broken pool, I need to create some storage space for the stuff that's on there now, so I'll dig deep in the hardware box and assemble a temporary zpool from some old drives - which I can also use to test how ZFS deals with swapping dd'd drives.

This might take a while...


Update 02:

This did take a while indeed. I've spent months with several open computer cases on my desk with various amounts of harddrive stacks hanging out and also slept a few nights with earplugs, because I could not shut down the machine before going to bed as it was running some lengthy critical operation. However, I prevailed at last! :-) I've also learned a lot in the process and I would like to share that knowledge here for anyone in a similar situation.

This article is already much longer than anyone with a ZFS file server out of action has the time to read, so I will go into details here and create an answer with the essential findings further below.

I dug deep in the obsolete hardware box to assemble enough storage space to move the stuff off the single 500GB drives to which the defective drives were mirrored. I also had to rip out a few hard drives out of their USB cases, so I could connect them over SATA directly. There was some more, unrelated issues involved and some of the old drives started to fail when I put them back into action requiring a zpool replace, but I'll skip on that.

Tip: At some stage, there was a total of about 30 hard drives involved in this. With that much hardware, it is an enormous help to have them stacked properly; cables coming loose or hard drive falling off your desk surely won't help in the process and might cause further damage to your data integrity.

I spent a couple of minutes creating some make-shift cardboard hard drive fixtures which really helped to keep things sorted:

some of the make-shift storage space just a bunch of screws plus some cardboard the fan is not exactly required, the stack is from an earlier project the distance pieces aren't required either...

Ironically, when I connected the old drives the first time, I realized there's an old zpool on there I must have created for testing with an older version of some, but not all of the personal data that's gone missing, so while the data loss was somewhat reduced, this meant additional shifting back and forth of files.

Finally, I mirrored the problematic drives to backup drives, used those for the zpool and left the original ones disconnected. The backup drives have a newer firmware, at least SeaTools does not report any required firmware updates. I did the mirroring with a simple dd from one device to the other, e.g.

sudo dd if=/dev/sda of=/dev/sde

I believe ZFS does notice the hardware change (by some hard drive UUID or whatever), but doesn't seem to care.

The zpool however was still in the same state, insufficient replicas / corrupted data.

As mentioned in the HPA Wikipedia article mentioned earlier, the presence of a host protected area is reported when Linux boots and can be investigated using hdparm. As far as I know, there is no hdparm tool available on FreeBSD, but by this time, I anyway had FreeBSD 8.2 and Debian 6.0 installed as dual-boot system, so I booted into Linux:

user@host:~$ for i in {a..l}; do sudo hdparm -N /dev/sd$i; done

 max sectors   = 976773168/976773168, HPA is disabled
 max sectors   = 976771055/976773168, HPA is enabled
 max sectors   = 976771055/976773168, HPA is enabled
 max sectors   = 976771055/976773168, HPA is enabled
 max sectors   = 976773168/976773168, HPA is disabled

So the problem obviously was that the new motherboard created a HPA of a couple of megabytes at the end of the drive which 'hid' the upper two ZFS labels, i.e. prevented ZFS from seeing them.

Dabbling with the HPA seems a dangerous business. From the hdparm man page, parameter -N:

Get/set max visible number of sectors, also known as the Host Protected Area setting.
To change the current max (VERY DANGEROUS, DATA LOSS IS EXTREMELY LIKELY), a new value
should be provided (in base10) immediately following the -N option.
This value is specified as a count of sectors, rather than the "max sector address"
of the drive. Drives have the concept of a temporary (volatile) setting which is lost on
the next hardware reset, as well as a more permanent (non-volatile) value which survives
resets and power cycles.  By default, -N affects only the temporary (volatile) setting.
To change the permanent (non-volatile) value, prepend a leading p character immediately
before the first digit of the value. Drives are supposed to allow only a single permanent
change per session. A hardware reset (or power cycle) is required before another
permanent -N operation can succeed.

In my case, the HPA is removed like this:

user@host:~$ sudo hdparm -Np976773168 /dev/sde

 setting max visible sectors to 976773168 (permanent)
 max sectors   = 976773168/976773168, HPA is disabled

and in the same way for the other drives with an HPA. If you get the wrong drive or something about the size parameter you specify is not plausible, hdparm is smart enough to figure:

user@host:~$ sudo hdparm -Np976773168 /dev/sdx

 setting max visible sectors to 976773168 (permanent)
Use of -Nnnnnn is VERY DANGEROUS.
You have requested reducing the apparent size of the drive.
This is a BAD idea, and can easily destroy all of the drive's contents.
Please supply the --yes-i-know-what-i-am-doing flag if you really want this.
Program aborted.

After that, I restarted the FreeBSD 7.2 virtual machine on which the zpool had been originally created and zpool status reported a working pool again. YAY! :-)

I exported the pool on the virtual system and re-imported it on the host FreeBSD 8.2 system.

Some more major hardware upgrades, another motherboard swap, a ZFS pool update to ZFS 4 / 15, a thorough scrubbing and now my zpool consists of 8x1TB plus 8x500GB raidz2 parts:

[user@host ~]$ sudo zpool status
  pool: zpool
 state: ONLINE
 scrub: none requested

zpool       ONLINE       0     0     0
  raidz2    ONLINE       0     0     0
    ad0     ONLINE       0     0     0
    ad1     ONLINE       0     0     0
    ad2     ONLINE       0     0     0
    ad3     ONLINE       0     0     0
    ad8     ONLINE       0     0     0
    ad10    ONLINE       0     0     0
    ad14    ONLINE       0     0     0
    ad16    ONLINE       0     0     0
  raidz2    ONLINE       0     0     0
    da0     ONLINE       0     0     0
    da1     ONLINE       0     0     0
    da2     ONLINE       0     0     0
    da3     ONLINE       0     0     0
    da4     ONLINE       0     0     0
    da5     ONLINE       0     0     0
    da6     ONLINE       0     0     0
    da7     ONLINE       0     0     0

errors: No known data errors

[user@host ~]$ df -h
Filesystem         Size    Used   Avail Capacity  Mounted on
/dev/label/root     29G     13G     14G    49%    /
devfs              1.0K    1.0K      0B   100%    /dev
zpool              8.0T    3.6T    4.5T    44%    /mnt/zpool

As a last word, it seems to me ZFS pools are very, very hard to kill. The guys from Sun from who created that system have all the reason the call it the last word in filesystems. Respect!

  • 3
    Before you do anything, image those drives! Take a backup of your 'corrupt' data in case you make it worse.
    – MikeyB
    Aug 5 '11 at 20:16
  • yep, that's a very good point! and it's also the reason why i haven't updated this article with my progress yet - still busy clearing out replacement hard drives...
    – ssc
    Aug 6 '11 at 4:47
  • I know - really old post, but THUMBS UP FOR THIS GREAT cardboard stack. I love it! Feb 5 at 11:02

The problem was that the new motherboard's BIOS created a host protected area (HPA) on some of the drives, a small section used by OEMs for system recovery purposes, usually located at the end of the harddrive.

ZFS maintains 4 labels with partition meta information and the HPA prevents ZFS from seeing the upper two.

Solution: Boot Linux, use hdparm to inspect and remove the HPA. Be very careful, this can easily destroy your data for good. Consult the article and the hdparm man page (parameter -N) for details.

The problem did not only occur with the new motherboard, I had a similar issue when connecting the drives to an SAS controller card. The solution is the same.


The very first thing I would recommend you do is to get some more hard drives and make duplicate copies of the 8 drives you have with your data on them, using the dd command. That way, if in your attempts to recover them you end up making things worse, you can still go back to this baseline.

I've done this before and there were times I didn't need it, but the times I did need it made it totally worth the effort.

Don't work without a net.

  • Actually, I would recommend ddrescue over dd. It doesn't really work much differently when the drives are functioning perfectly (but it does give you a nice progress indication) but if there are any problematic sectors or something like that, ddrescue handles that situation far better than dd does (or so I've been told).
    – user
    Nov 4 '16 at 22:34

You seem to be on track to solving this. If you want another, possible newer point of view you could try a Solaris 11 Express live CD. There's likely a lot newer code running there (zpool in Solaris is now at version 31, whereas you are at version 6) and it might offer better recovery possibilities. Don't run zpool upgrade under Solaris though if you want to keep the pool mountable under FreeBSD.

  • Thanks for that tip! :-) I was looking into OpenSolaris back in 2009 or so when I started this whole ZFS business, but unfortunately, it did not support the controllers I'm using - this is consumer grade hardware after all. Just recently, I've also looked at OpenIndiana, but I'm not sure if the situation has changed. I might upgrade the controllers to SAS at some stage and consider migrating then.
    – ssc
    Aug 10 '11 at 3:26
  • I think OpenIndiana might be worth a new look. If nothing else, they might be more friendly to "cheap" hardware than Oracle... I recommended the live CD because it's easy to try out -- you can run it in a VM as well.
    – Jakob Borg
    Aug 10 '11 at 7:02

The FreeBSD mailing lists might be a good starting point for your search. I remember having seen similar requests go by on FreeBSD-Stable and -Current. Depending on the importance of your data, you might wish to contact a professional recovery firm, however, as tampering with inaccessible data storage pools carries a good chance of making things worse.


I experienced a similar issue after upgrading from FreeBSD 10.3 to 11.1, afterwards the zpool was faulted and there was no way to recover the data, even though zdb -lll returned all four labels valid.

It turns out that somehow the update triggered the Intel storage management drivers to create a softraid mirror out of the disks (perhaps it was enabled but not supported by geom's Intel provider until post-update?) and that blocked ZFS from mounting the disks.

Attaching them to another PC with Intel RST boot-time firmware enabled and disabling the softraid (very important: there are two ways to break the softraid, the default of which initializes (aka formats!) the disks. You need to choose the option to disable without touching the data instead) then let ZFS recognize the first disk in the mirror, though nothing I did would allow it to identify the remaining disks as being the same that were in the machine pre-update. Fortunately it was a mirrored zpool and I was able to just detach and reattach the disks to the pool in question and the resilver completed without event.

Side note: In my case, hdparm (running from a live Ubuntu Server ISO) reported that HBA was disabled on all disks and was not able to help.


if it was just a partition issue of some kind i would dd the drive partitions+ MBR and just make the partition the right size ...

if you don't format a partition creating or changing the partition table does not affect anything ( so you can roll back that !) as long as there is no format then most of the data is still there /accessible if the new partition is inserted at the end of the drive you might have corrupt files there where the new stuff was writen tough thats why your only good for that trick till you format ( new mbr ,file table etc...)

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.