As discussed in a previous question, we have 6 OWC Mercury Extreme SATA SSD drives installed in our HP Proliant DL360 G7 server (using a P410i RAID controller). They work great, and are very fast. However, I'm aware that SSD drives unfortunately don't last forever, and the HP ACU utility, not surprisingly, won't monitor the health of any of the drives:

enter image description here

Does anyone know of any Windows (Server 2008R2) software or utilities that will allow monitoring of the health of each individual drive in the array, so that we can proactively pick up on any potential issues?

  • I'll let ewwhite or someone that really knows run with the answer, but I did find this for you. "HP Solid State Drives are equipped with tools that can report the amount of lifetime remaining. Introducing HP SMARTSSD Wear Gauge™. In order to take advantage of SMARTSSD Wear Gauge™, Smart Array Firmware version 5.0 or greater is required and HP Array Configuration Utility (ACU) or HP Diagnostic Utility (ADU) must be running"
    – TheCleaner
    Commented Aug 20, 2013 at 19:07
  • 1
    @thecleaner Do I have to answer!?!
    – ewwhite
    Commented Aug 20, 2013 at 19:49

2 Answers 2


You can use smartctl to peek at individual drives behind a cciss RAID controller like so:

smartctl -a -l ssd /dev/sda -d cciss,1


smartctl -a -l ssd /dev/sda -d sat+cciss,1

(you may need to remove -l ssd if your smartctl is too old)

  • What does the "1" after cciss denote?
    – ewwhite
    Commented Aug 21, 2013 at 7:22
  • Got it. Drive position. The second command string works on the ProLiant with these disks. Here's the output.
    – ewwhite
    Commented Aug 21, 2013 at 7:29
  • @ewwhite you'll see more data with an updated version of smartmontools. Clone the repo, build it, then run it out of the directory. No need to install if you don't want to.
    – MikeyB
    Commented Aug 21, 2013 at 14:46

Don't bother... Really.

You have an enterprise server with an enterprise RAID controller and hot-swappable drives (with a 5-year warranty), presumably in a RAID 1+0 setup. Do you care why a drive fails beyond the fact that it fails? I don't. I wouldn't care why a spinning disk died either (S.M.A.R.T. errors, bearing failure, overheating, etc.)

High-end (SAS) HP Solid State drives do provide some additional health information. But if you're using RAID and know where to get a spare, I don't think this information is tremendously helpful. You get temperature readings and an "Estimated Life Remaining" figure.

That is all.

  physicaldrive 1I:1:4
     Port: 1I
     Box: 1
     Bay: 4
     Status: OK
     Drive Type: Unassigned Drive
     Interface Type: Solid State SAS
     Size: 400 GB
     Firmware Revision: HPD9
     Serial Number: 00197356
     Model: HP      MO0400FBRWC     
     Current Temperature (C): 29
     Maximum Temperature (C): 43
     Usage remaining: 99.57%
     Power On Hours: 6418
     Estimated Life Remaining based on workload to date: 61922 days
     SSD Smart Trip Wearout: False
     PHY Count: 2
     PHY Transfer Rate: 6.0Gbps, Unknown
  • One good reason: it allows you to monitor the life of your SSD and potentially extend their life by moving them to a lower-demand server when they approach their expected life.
    – MikeyB
    Commented Aug 20, 2013 at 20:53
  • These disks are in a RAID array. TRIM commands aren't being passed through the controller. The drives are over-provisioned (15%) and it's just as easy to keep a spare or just leverage the warranty. I don't see people encounter SSD wearout on appropriately-spec'd drives often.
    – ewwhite
    Commented Aug 20, 2013 at 20:56
  • They probably won't encounter SSD wearout, but it's still very useful to be able to demonstrate this. The SMART wearout counter is likely to hit the threshold at which SMART reports the drive as failed at the same time, more or less, on all the drives. Having a spare won't help you if all your drives are marked bad at the same time, but being able to predict that you'll need to replace them in so many days is useful. Commented Aug 21, 2013 at 3:04
  • I have an OWC Electra SSD in a system, and it has a Sandforce controller which reports SSD life left as a pre-fail condition. Once it hits this threshold, SMART will mark it as failing. An Intel 320, on the other hand, reports life as an old-age condition, so SMART won't say the drive is failing once it hits wearout. Given that OPS has a non HP-drive in the array, and behaviour at SMART wearout is perhaps uncertain, I'd err on the side of caution and make sure I know when I'm going to hit that wearout point. Commented Aug 21, 2013 at 3:11
  • HP controllers factor SMART statistics into the drive health equation. Behavior IS known. I'm the one who recommended the solution :)
    – ewwhite
    Commented Aug 21, 2013 at 7:16

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .