39

My HP Proliant ML110 G7 has a full-size SD slot on the motherboard. What is its use case?

The PDF manual mentions it on page 10: item 17 just to show its placement, but nothing more. In a later revision (Gen 9), it is said the slot is not hot-pluggable.

HP Proliant ML110 G7-motherboard

The motherboard also has a USB slot (item 11).

Improve this question
3
  • 1
    Some system even offer adual sdcard slot to make a mirror of them for your system
    – yagmoth555 ♦
    Jan 3, 2017 at 1:57
  • 1
    I have several dell R610 servers that have 1 Gbyte of flash on the mainboard, and no hard drives/no backplane. Had they been built with a SD slot I could have upgraded the card and continued using them, instead of parking them in the spare parts store.
    – Criggie
    Jan 4, 2017 at 6:16
  • But you can use them: boot off from USB/PXE, mount a NFS/iSCSI share and you are done...
    – shodanshok
    Jan 11, 2017 at 8:36

4 Answers 4

Reset to default
60

It's for booting a hypervisor or lightweight operating system like VMware ESXi.

See: What happens when the USB key or SD card I've installed VMware ESXi on fails?

Improve this answer
1
  • That explains the "not hot-swappable" warnings on HP Gen8 spec sheets!
    – Kristen Waite
    May 14, 2018 at 13:30
20

By installing an embedded hypervisor/OS on the SD card, you leave all the front-bay disks available for data storage. This is an useful logical and practical separation.

Some servers have two RAID1-ed SD slots: if a single SD fails, the system continue to run from the mirror, leaving you the time to replace the failed SD.

The most widely installed embedded hypervisor probably is ESXi, with a footprint less than 2 GB.

Improve this answer
5
  • My motherboard has also a USB slot. I doubt they can be raid-ed though.
    – FarO
    Jan 3, 2017 at 23:28
  • The USB port is mainly intended to put in a USB stick if you need to transfer some extra data (like drivers) to the server while you are installing it.
    – Tonny
    Jan 4, 2017 at 14:57
  • 2
    @Tonny I think the OP is talking about an internal USB slot, which is used exactly as the SD one: to install an embedded OS/hypervisor without touching the data disks.
    – shodanshok
    Jan 4, 2017 at 15:45
  • For a while, the internal USB port was sometimes intended to run a tape drive.
    – Criggie
    Dec 5, 2017 at 4:02
  • 1
    My Supermicro X-10 series motherboard has a USB B connector mounted on the board. I use it to hold the OS, a dedicated NAS appliance. @Criggie it's odd that your internal tape drive did not have a jumper-header connector instead.
    – JDługosz
    Dec 5, 2017 at 9:24
2

You can use the SD card for example to outsource the /boot partition. e.g HP ProlianG8 G8 can not boot from HDD when the RAID controller is configured to HBA but you can still boot from the SD-Card.

Also you may by able (not tested) to outsource EFI fat partiotion to the SD-Card to by able to create a software RAID and load kernel / init from there.

FYI: Unfortunately the internal SD Card slot on Supermicro motherboards cannot be used for OS / boot partition and according to Supermicro is reserved for internal debugging use only

https://www.supermicro.com/support/faqs/faq.cfm?faq=29646

Improve this answer
1

Some years ago, the embedded PC motherboard used in a product had a CF card slot on the motherboard. The SD is probably a modern update to that.

For a device that will run embedded firmware, not a desktop or conventional server (e.g. a specialized medical imaging printer) this is a specific feature desired of the board.

As I recall, it was running Embedded XP, an older MS product for that purpose.

Improve this answer

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge that you have read and understand our privacy policy and code of conduct.

Not the answer you're looking for? Browse other questions tagged or ask your own question.