Is it possible to reset the password on a SuperMicro IPMI interface? My motherboard is model X8STI-F.
If you access it locally you can specify a new password. On Linux this would be done via
ipmitool. Something like this should work:
ipmitool -I open lan set 1 password NEWPASSWORD
If you don't know which channel is your ethernet interface, just page through them one at at time, like so:
# ipmitool -I open channel info 1 Channel 0x1 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : enabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : enabled Access Mode : always available
Note that the medium type is "802.3 LAN". That's the one you want. Other channels may look like this:
# ipmitool -I open channel info 2 Channel 0x2 info: Channel Medium Type : Serial/Modem Channel Protocol Type : IPMB-1.0 Session Support : single-session Active Session Count : 0 Protocol Vendor ID : 7154 # ipmitool -I open channel info 3 Channel 0x3 info: Channel Medium Type : System Interface Channel Protocol Type : KCS Session Support : session-less Active Session Count : 0 Protocol Vendor ID : 7154
I just had to deal with this same issue yesterday, I was not able to log into my SuperMicro IPMI web interface because I had not used it frequently and forgot the password. The command in Insyte's answer did not work for me but it was close. This command worked to reset the ADMIN account's password:
ipmitool -I open user set password 2 ADMIN
The number 2 there is the user id. The ADMIN account defaults to user id 2. So I'm setting user id 2's password to ADMIN which is the default, but you could put any other password there.
Thank you to Insyte for pointing me on the right track of using ipmitool, after a few searches online I was able to find this working command. Hopefully it will help someone else that stumbles on this question.
Supermicro IPMI BMCs can be fairly erratic and troublesome. You should always use the utilities and tools provided by Supermicro before attempting a fix with universal tools such as IPMITool.
It is not necessary to reset the entire unit as others have suggested.
If you have physical access to the server, follow these simple steps to reset the ADMIN password on your IPMI:
- Create a bootable DOS USB stick using Rufus.
- Download the latest IPMICFG utility released by Supermicro.
- Extract the archive and copy the contents of the 'DOS' folder on to your bootable DOS USB.
- Boot your server into DOS and navigate to the 'DOS' folder you copied on to the USB.
Get the user ID of the IPMI user whose password you want to set:
ipmicfg -user list
Set a new password for that user (the ADMIN user typically has an ID of 2):
ipmicfg -user setpwd 2 your_password_here
Login to the IPMI web GUI using the password you just set.
I've reset the ADMIN password on dozens of Supermicro IPMI BMCs. Of all the methods I've tried, this is the only procedure that works 100% of the time.
Note: If you already have Windows or Linux installed on your system, then you can skip steps 1, 3 and 4 and merely execute the commands in steps 5 and 6 using the appropriate executable from the Supermicro toolkit downloaded in step 2. If you are using Linux and you encounter
kcs_error_exit messages when invoking
ipmicfg commands, then you need to install the OpenIPMI library and enable the
ipmi_devintf kernel module.
The following commands work on CentOS 6:
yum -y install OpenIPMI modprobe ipmi_devintf
Remember that the command
modprobe ipmi_devintf will need to be re-run every time you reboot the server.
Best way is to reset to defaults and clear FRU&LAN with SuperMicro native tool, like so:
(All this may take a few seconds to take effect, so wait between commands!)
Now turn off the DHCP setting restored from factory defaults with
./ipmicfg-linux.x86_64 -dhcp off
then, restore your network settings with:
./ipmicfg-linux.x86_64 -m $IP_ADDRESS ./ipmicfg-linux.x86_64 -k $NETMASK ./ipmicfg-linux.x86_64 -g $GATEWAY_IP
I've noticed, that sometimes, you need to reset BMC unit for it to take effect. Just today, was unable to ping my server's IPMI IP address set via ipmicfg utility until after BMC reset:
You'll have to configure the IP/Netmask/Gateway again with the same tool, but this is the only way I could make it work.
OpenIPMI and IPMITools did not work for me on Debian Squeeze. I've tried resetting the password, cold resetting BMC, to no avail. However, they are good for setting IP and reading sensor data.
You can get the appropriate version for your OS from SuperMicro FTP:
This simple answer is different than then others which need some other formal OS installed to reset the password.
Boot a thumb drive with the proper IPMI firmware file and the proper flashing utility for your motherboard from SuperMicro's website. We use a dos based one for simplicity. If you already have the current IPMI firmware Simply flash it with the same version you already have.
Most of our systems are X8 based boards that have onboard IPMI. These use YAFUKcs (Yet Another Firmware Updater).
If you normally save the config while updating, simply leave off the -c option
yafukcs -full romfile.ima instead of
yafukcs -full -c romfile.ima
Interestingly enough, leaving off the
-c option does not cause IPMI static addressing to be reset in the BIOS. It only affects settings within the IPMI environment, such as LDAP, NTP and any alert notifications you have configured.
You should consider flashing the system BIOS after the IPMI update, however it isn't required. If you flash the system BIOS, those settings will be reset, but the IPMI LAN settings will not change.
The suggested solutions did not work for me on my SuperMicro X11SCL-F running Ubuntu 18.04. Here is how I was able to successfully reset the ADMIN password:
ipmitool user set password 2
It then prompts you to enter the new password. Hope this helps somebody out there. After that, just use the web interface to login with
ADMIN / #NEWPASS#