5

I have a case fan that can be quite noisy. I can take the fan out of the case, peel back the sticker on the center to expose access to the bearings, and lubricate the fan. Thus far, I've been using a few drops of WD-40, but after a few days the fan makes noise again.

Obviously, I could buy a new fan, but knowing how to lubricate a noisy fan seems somewhat useful, as not all hardware hardware has replaceable fan units.

Does anyone know why the WD-40 only works temporarily, and what I should be using instead?

8

I'd try 3 in one oil. WD-40 is mostly a solvent, 3 in one should give you a longer term solution.

20

You should really replace the fan. The ball bearing has probably seized and adding lubrication will only help for a few days. As a temporary lubricant you could use about anything with low friction.

  • 2
    Worse, most fans are sleeve bearing and don't last that long. Purchase a quality ball bearing fan. – Brian Knoblauch Dec 16 '09 at 16:09
  • 5
    +1: It's a cheap part, and one that shouldn't require maintenance during its design life. (Shouldn't use WD-40 anyway; 3-in-1 oil for bearings.) – Satanicpuppy Dec 16 '09 at 16:09
  • 1
    Disagree. I've seen many noisy fans "get better", and often last the life of the machine (4-5+ years total). – Boden Dec 16 '09 at 16:40
  • 2
    +1: The amount of labor you spend relubricating the fan will almost certainly eclipse the cost of replacing the fan. – rob Dec 16 '09 at 18:04
  • 1
    I've oiled fans and had them run for years afterwards. 3-in-1 or sewing machine oil. Useful for high quality but old fans. Not so useful for fans that were cheap to start with. – Grant Aug 23 '12 at 19:56
2

Clean it out and use a vegetable based oil with a pin hole oil lubricator. It looks like a pen. You can get them at a hardware store. Or just replace the fan you cheapo.

2

Aerosol Teflon is another option.

1

I do what you're suggesting quite frequently. I put a few drops of WD40 down into the bearing, and then I use a high pressure air hose to spin the fan real fast. I then take a paper towel and wipe out the gunk. I might repeat the process one more time. Then I put a drop or two of 3 in 1 oil in there and give it another good spin.

After having done this dozens of times with fans of various size and make, I would say that it restores fan life for a considerable period. Sometimes the fan will start chattering again after a year or so and I'll repeat the process. In only a few situations have I ever had to buy a new fan. It's not that I'm cheap, it's that finding a replacement fan can be an irritating process..especially if it's some goofy chipset fan with a unique mount. This process only takes ten minutes, and so far I've found it less time consuming than trying to find a replacement.

One exception I make is for power supply fans. I don't open those things up anymore. I typically just buy a new supply.

  • You clearly have a lot of free time. – Satanicpuppy Dec 16 '09 at 17:17
  • 1
    Yep, ten whole minutes every now and then. – Boden Dec 16 '09 at 18:53
0

I notice that amazon is offering one heck of a deal on 55 gallon drums of lube - almost two thirds off! I'm not sure how well this type of lube would work on a fan, and the fact that it's water-based would make me a little wary of using it on an electronic component, but seeing as how your fan should probably be replaced anyway, it seems like a perfect opportunity to try something a little bit "out there."

0

The Definitive Proper Method to lubricate a noisy fan, it will work on most fans and it will continue to work longer than expected in most cases.

WD40 is a great start only, and clears some old oil crap out, but then dries out completely, and I really like WD40 for this action, if a fan is grimy, use it and wait a day or blow-out or dap-out excess WD40.

The Method That Really Works: DuraLube - TRUST ME An ink syringe or regular syringe with DuraLube use 1 or 2 or 3 drops only, 1 drop is for a near working fan, 2 drops for a lightly dirty or larger fan, 3 drops for an ugly stuck but moving sleeve bearing,

I've used everything including Slick50, Nothing works better than DuraLube on computer Fans and they run one and a half to 3 years longer and whats more amazing is you can do it again on the same fan 3 years later.

Do It - be unsuprised at how you forget that the fan ever had a problem, work really good on Fridge fans.

Now I need a way to do this for fans without holes, if anyone knows a definitive way, please let us know.

New contributor
Tom Holt is a new contributor to this site. Take care in asking for clarification, commenting, and answering. Check out our Code of Conduct.

Your Answer

By clicking "Post Your Answer", you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.