Questions tagged [hp-procurve]
ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.
146
questions
2
votes
3
answers
3k
views
ProCurve ACL to prevent a subnet from leaving the switch
I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (...
1
vote
3
answers
5k
views
Fibre (Fiber) Optic - Mixing SFP's and Switches
My generic question is: Can you mix switches on the opposite sides of a fibre link, or more accurately different manufactuors tranceivers.
We just bought several new HP ProCurve v1810 series switches ...
2
votes
2
answers
5k
views
VLAN security on HP ProCurve 1810G-24?
I'm looking into the managed switch HP ProCurve 1810G-24 to see if it can meet our office demands. The specs say it has IEEE802.1Q - whatever that means.
Our office consists of four companies that ...
1
vote
1
answer
2k
views
HP Procurve to Cisco - QOS
I have a HP Procurve with the following:
vlan 4
name "Phones"
untagged 20
ip address 10.50.60.1 255.255.252.0
qos dscp 101110
qos device-priority 10.50.100.10 dscp 101110
qos device-...
3
votes
1
answer
4k
views
Rate Limiting with HP ProCurve 5406 QOS
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP address on a specific port?
We have a 10Mbps head end connection for multiple ...
-2
votes
2
answers
2k
views
VLAN routing issue
I have HP Procurve Switch 2910AL-24G.
Please see attached configuration.
Client inst2is01 (10.247.167.80) and VLAN ID is 37
Server ILO (Management Port) IP : 10.247.172.70 and VLAn ID is 54
From ...
3
votes
1
answer
2k
views
vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?
I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is ...
8
votes
2
answers
5k
views
HP Procurve Issue Passing Multiple VLANs over a link
Just to start off with I am a Cisco guy that got placed into an HP project.
Basic topology overview from outside in:
ASA 5505 with two Ethernet connections to a 2610 switch.
This switch is then ...
3
votes
1
answer
16k
views
ProCurve 2610 Java error?
I've got two identical procurve 2610-24/12PWR switches with the web interface configured. I can log in to one and see all the management info just fine. When I load the web interface of the other I'...
2
votes
2
answers
894
views
Adding second HP 2410G-24 Switch
We have a single HP Procurve 2410G-24 Switch.
For the sake of simplicity, there are 2 VLANS configured, and the ports are roughly equally split between them. VLAN1 (LAN) is for server LAN connections,...
8
votes
3
answers
12k
views
dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches
We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets ...
1
vote
0
answers
927
views
Where is HP Procurve route type "ICMP" coming from?
I've got the following test network:
Architecture:
edge_a: 192.168.e.1 [edge vlan] (edge switch, no acl) [admin vlan] 192.168.m.1/24
core: 192.168.m.2/24 [admin vlan] (core router, yes acl) [...
2
votes
3
answers
490
views
Cisco 4900M trunk to HP ProCurve switch. Will this setup work?
As I previously ran a Cisco only shop I'm not sure if this is going to work. On paper it looks OK, but you never know.
Will it work ? Are there special considerations that I need to be concerned ...
0
votes
1
answer
3k
views
HP E3800 series Web GUI times out
I am having some trouble with the web interface for my new E3800 (3800-48G-4SFP+ Switch (J9576A)). I have two of them stacked in a ring topology. When I restore to the factory default and add an IP ...
2
votes
1
answer
759
views
Procurve 5400 10GB
I need some help for 10GB connection. I actually have a Procurve 5400zl series with some port SFP+ on V2 version module. We desperately need to connect a server with pci-x slot.
what can I do to have ...
1
vote
1
answer
4k
views
Spanning tree problems in a shared HP ProCurve environment
we're sharing a server room with another company, including the network infrastructure. All the switches are HP ProCurve, in various models depending on port need and so on. We're using VLANs to ...
3
votes
2
answers
21k
views
HP Procurve 1800 Switch-to-Switch Trunks and LACP (and VLANs too!)
I am considering connecting two (and possibly three) HP Procurve 1800 switches together with trunks or with LACP. I can't find any substantial answer to my questions via Google or here.
I did find ...
1
vote
0
answers
686
views
HP ProCurve & Cisco switches interoperability
I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below ...
4
votes
2
answers
652
views
ProCurve 1800 switch issue
I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, ...
2
votes
1
answer
334
views
Wifi hosts can't contact one another (but wired hosts on the same vlan can)
Our current network is vlan'd, and the wifi network is on its own separate vlan (130).
To connect to the 130 vlan, you connect to the access point (a HP MSM310), which is connected to an HP Procurve ...
5
votes
1
answer
2k
views
Setting up Multicast NLB Cluster with HP 6120XG Switch
How can I setup an NLB cluster across 2 blades connected via a HP 6120XG Switch? All of the guides are for Cisco and setup static ARP entries on the switch but that is not possible on the HP Switch.
...
5
votes
1
answer
23k
views
HP Procurve 5406ZL - How to enable port-mirroring?
How would you enable port mirroring for a HP Procurve 5406ZL?
The configuration guide is not very clear in the mirror-port function. I know that I'll need to use the mirror-port [[ethernet] PORT-NUM]...
7
votes
1
answer
4k
views
How to configure a HP Procurve network for IPv4+IPv6
The setup:
We are an apartment complex with approximately 1700 units. Every apartment has internet with an ethernet plug in each. The network has 60 HP 2910al-48G switches connected to a central HP ...
9
votes
1
answer
13k
views
Admin mode on Procurve Switches
Not being a network expert, I spent some time configuring my network, until I found my mistake: On my HP ProCurve Switch 1810G, I thought that "Admin mode" means whether the administrative interface ...
8
votes
2
answers
765
views
Network traffic doesn't appear to leave the trunk
I'm in the process of staging up some new virtualization servers, and part of that is to get some higher-bandwidth pipes into them. The ultimate goal is to bind 4 GigE ports into a single trunk ...
2
votes
1
answer
1k
views
HP switch 'mirror port' makes a Cisco switch port err-disabled due to keepalive loop-back
I'm trying to connect an HP ProCurve 5304xl switch to a Cisco 2950. The HP port I'm connecting to is described as a 'mirror port', which appears to be like a SPAN port except that it also allows ...
5
votes
1
answer
3k
views
HP Procurve MAC cache timeouts on long TCP sessions
We have a network of HP 2510G switches connected back to HP2912al for aggregation. We've noticed that long running connections like a MySQL DB dump start flooding out to all network ports once the ...
5
votes
1
answer
20k
views
Procurve 2810 command line - reassigning ports to a different VLAN
A very basic question, but my googling has failed to find an answer...
At present the VLAN config looks like this:
vlan 1
name "DEFAULT_VLAN"
untagged 1
ip address 10.200.1.134 255....
4
votes
2
answers
6k
views
How to calculate required switch speed based on network usage?
I have a 48 100Mbit/s port HP Procurve Switch 2610 (J9088A) that can handle 13.0 million PPS (packets per second) and features wire speed switching capacity at 17.6Gbps.
First off, what does that ...
8
votes
3
answers
10k
views
Setup of HP ProCurve 2810-24G for iSCSI?
I have a pair of ProCurve 2810-24G that I will use with a Dell Equallogic SAN and Vmware ESXi.
Since ESXi does MPIO, I am a little uncertain on the configuration for links between the switches. Is a ...
4
votes
1
answer
4k
views
10 GigE interfaces limits single connection throughput to 1 Gb on a ProCurve 4208vl
The setup is as follow : 3 Linux servers with Intel CX4 10 GigE controllers and an X-Serve with a Myricom 10 GigE CX4 controller are connected to a ProCurve 4208vl switch, with a myriad of other ...
1
vote
3
answers
7k
views
Cisco Catalyst VTP to HP ProCurve GARP?
I have two L3 capable ProCurve switches (2810-24G) which I would like to use in our Cisco environment.
The Cisco switcheshave vtp configured, and all VLANs are added/maintained basically on the ...
1
vote
0
answers
2k
views
Load-balancing between a Procurve switch and a server
I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work?
My ...
0
votes
2
answers
21k
views
How to use a MIB file
I have a HP 2626 switch and want to monitor it by SNMP. how can i use the MIB file.
Any starting points on how to understand it ?
using snmpwalk to get the data in a *nix machine and output it in a ....
4
votes
3
answers
12k
views
Connecting a USB laptop to a RJ45 serial port
We are about to get our first managed switch at work (Procurve 2520G-24-PoE), and this lowly programmer gets to put on his admin hat and try to configure it. The switch has an RJ45 serial port for ...
1
vote
1
answer
594
views
Procurve Switch Multiple Gateways
I have a Procurve 3500yl switch that is currently handling all of the VLANs and the default gateway for my network. Currently, the gateway is set to our old FreeBSD firewall/router and I am trying to ...
54
votes
5
answers
43k
views
How exactly & specifically does layer 3 LACP destination address hashing work?
Based on an earlier question over a year ago (Multiplexed 1 Gbps Ethernet?), I went off and setup a new rack with a new ISP with LACP links all over the place. We need this because we have individual ...
0
votes
1
answer
1k
views
HP MSM410 WAP Wireless security mode: restrict to default gateway or off?
I have an HP MSM410 wireless access point and when I first configured it I couldn't access any other devices on the network, but I could access the internet fine. I figured out that this was because ...
2
votes
1
answer
885
views
Bonding NICs with Procurve 1400-24G switch
I was looking to bond two or three NICs together to increase throughput. Now, this should be straight forward if done computer to computer, but since there are 3 computers involved which require ...
0
votes
2
answers
1k
views
Autonegotiate errors between HP and Cisco hardware?
This is a bit of a specific extension to this question.
I've got two ASA's that feed into a Procurve switch, and then into an IPS. All is well except that the procurve absolutely refuses to ...
1
vote
1
answer
4k
views
Is it possible to change the voltage on a single port on an HP ProCurve 2910al POE switch and how?
I have a couple of HP ProCurve 2910al POE+ switches at my company that we are primarily using to power our VOIP phones that run on 48V DC. However, I have one wireless access point that I need to run ...
1
vote
2
answers
998
views
Using a Level 2 switch as a core switch
I have a small user base of about 20 people on at a time and spiking up to about 80 people during peak times. Most people (80+%) are connected over our Aruba managed wireless system. We have a Windows ...
9
votes
3
answers
14k
views
Server-to-Switch Trunking in Procurve switch, what does this mean?
I am looking to set up switch redundancy in a new datacenter environment. IEEE 802.3ad seems to be the go-to concept on this, at least when paired with a technology that gets around the "single ...
1
vote
2
answers
4k
views
LAN Design Question with HP Procurve
HP Procurve 2510G-24 x 2 Port (For Servers) and 2 x HP Procurve 2510-48 Port 10/100 (For Desktops).
Topology is like :
Patching is terminated on 2nd floor and the servers are located on the 1st ...
9
votes
3
answers
3k
views
Automatic rollout of VLAN (and other) configs to Procurve switches
I've got a pile of switches connecting everything together at our DC, 50 racks or so worth of kit. It's starting to be a problem to login to every single one of them to make configuration changes -- ...
2
votes
1
answer
12k
views
Configuring VLAN's on two HP procurve switches
Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects ...