Questions tagged [hp-procurve]
ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.
30
questions with no upvoted or accepted answers
3
votes
0
answers
227
views
Only able to ping WiFi AP for about 60 seconds, then is full access after
I have 3 x Mikrotik RB951Ui-2HnD router board (RB) running 6.31 with wlan1 bridged with ethernet 2.
STP is disabled on the RB bridge (protocol mode set to None).
I have a HP ProCurve 2520-24-PoE ...
3
votes
1
answer
3k
views
DHCP Server Issuing NAK when servicing multiple subnets
We currently have 3 VLANs setup in our network. On our DHCP server (Windows 2008) we have 3 scopes created for the 3 separate subnets. Our clients can't seem to pull addresses on the subnets, except ...
2
votes
0
answers
656
views
NIC team not load balancing
I'm trying to achieve a load-balanced NIC team on a Windows Server 2016 machine. This is a ProLiant using a 4x 1Gb 311FLR interface card which as of yesterday has the latest driver installed (100.20.0....
2
votes
0
answers
3k
views
Protecting network from a broadcast storm
We have a flat office network tree built on a number of different ProCurve L2 and L3 GigE switches that spans some 300 ports. Today I found that one of the devices in the network for a short period of ...
1
vote
1
answer
137
views
Routing through a 2nd network with a Procurve 2848
I've got an old Procurve 2848 sat in the office I'm trying to figure out and struggling with.
I'm trying to setup a route through to my other network & out to the internet.
I have a Cisco ...
1
vote
0
answers
119
views
hp 2920 stack hot swap
I have 4x HP/Aruba 2920s configured in a stack using the dedicated stack hardware and cabling. All seems to be working well except for one issue:
On the first unit which is acting as the "commander",...
1
vote
1
answer
506
views
How do I enable the WIFI radio of an HP ProCurve 420ww Access Point?
So based on this old question of mine I figured out that I can reset the access point and access it using telnet through a wired Ethernet connection.
I have set a new password, I have set up the ...
1
vote
0
answers
328
views
ProCurve 2910 - ping lost on tagging
I can't figure this out. I have 2 HP 2910 switches, interlinked (A1).
VLAN 113 is management, I have an uplink to the core switch on port 20. Pinging and browsing works fine. However, I can't ping a ...
1
vote
1
answer
823
views
Procurve Inter VLAN Routing
I have a VLAN routing issue on our network. We have two ProCurve 5406zl's being used as our core switches, each vlan on these switches has an IP address and VRRP is configured on each vlan for ...
1
vote
0
answers
37
views
Losing connection to devices over the weekend
We have a networking scheme such as:
10.1.0.0/16
10.2.0.0/16
10.3.0.0/16
Each network is associated with a switch. Each switch connects to a layer 3 core switch that also acts as our router.
We ...
1
vote
1
answer
486
views
Two stacked HP 2900-48G switches. Now I need a couple SFP+ ports, possible?
I have two stacked HP 2900-48G switches in rack A.
Now in rack B I need a switch that provides at least two SFP+ ports (for two servers) and at the same time establish a 10G link to the switches in ...
1
vote
0
answers
509
views
Spanning Tree Protocol on HP5406zl and Netgear edge switches
I have a simple star network setup, a core HP switch with servers and storage, and WAN uplinks on it, and then trunked 2 x 1GB uplinks to some crappy old Netgear switches (I know, but moving on).
We ...
1
vote
0
answers
3k
views
HP ProCurve 4208vl - Show PSU information?
I'm working with a few older HP ProCurve 4200-series chassis switches (4204vl and 4208vl).
Some of these units have single power supplies, while others have dual power supplies. I'm trying to ...
1
vote
0
answers
684
views
VLAN configuration on HP J9279A
I've tried to set up separate VLAN for lab environment on one of my HP switches (J9279A/J9280A).
Network schema:
WAN
|
GW
|
...
1
vote
1
answer
139
views
HP Radio Port 210 web configuration
We acquired used WiFi system to provide better wlan for the customers in our hostel.
The switch is HP PROCURVE 5406zl and we have 50 or so HP PROCURVE RADIO PORT 210 access points.
I set up the ...
1
vote
1
answer
274
views
ProCurve Trunking
We have 3 switches at the moment - see the diagram below for NOW. Essentially the CORE switch is 7, and 8 and 9 have a 3 cable trunk each to 7.
Now, we want to add Switch 5 to the equation - see ...
1
vote
0
answers
661
views
Windows 2012 to HP Procurve redundancy across multiple switches - multi-switch LACP?
We are looking to have our Windows 2012 server(s) connected to two separate switches, so that if one switch goes down the server(s) can still be accessed on the same IP address from the switch that is ...
1
vote
1
answer
684
views
How to prevent partial crash during VLAN configuration on a HP ProCurve 3500
As you can see from my question, I have a VLAN configuration problem with a ProCurve 3500.
The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I ...
1
vote
0
answers
6k
views
HP Procurve 2910AL allow traffic from VLAN to VLAN
We are trying to setup so that the switch handel routing and communication between a few vlans.
And then have a link network up to the fw.
Here is the config:
Running configuration:
; J9145A ...
1
vote
0
answers
927
views
Where is HP Procurve route type "ICMP" coming from?
I've got the following test network:
Architecture:
edge_a: 192.168.e.1 [edge vlan] (edge switch, no acl) [admin vlan] 192.168.m.1/24
core: 192.168.m.2/24 [admin vlan] (core router, yes acl) [...
1
vote
0
answers
686
views
HP ProCurve & Cisco switches interoperability
I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below ...
1
vote
0
answers
2k
views
Load-balancing between a Procurve switch and a server
I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work?
My ...
0
votes
1
answer
88
views
Can modern switches limit packets based on IP without VLANs or bridge VLANs?
Can the switch HP 2910al, restrict traffic coming to it based on it's IP/subnet settings without using the routing functionality? Or is it possible to configure something like HP 2530 (layer 2) to ...
0
votes
1
answer
586
views
Intervlan routing in HP Procurve 2900 not working
Heya networking gurus!
I am building a Proof of concept that requires doing some wacky things. All is going well except I can not seem to get my intervlan routing working.
Here is a diagram of what ...
0
votes
0
answers
68
views
VLAN Routing for VOIP
Confession first - my networking skills are not massive but I'm learning fast!
We have three VLANs (for the sake of this question - there are actually more but not relevant to the posting). These are:...
0
votes
1
answer
135
views
Intervlan routing--DHCP offer from server on default VLAN not making it back to newly created vlan via layer 3 switch
Default VLAN: 10.36.0.0/24
New VLAN : 10.36.8.0/24
DHCP server : 10.36.0.17
I can see the DHCP offer packets making it back to my VLAN ip address namely 10.36.8.31 (from dhcp server message log)
...
0
votes
0
answers
41
views
Windows 7 Pro losing LAN connectivity but wireless systems are having no problems
We have 50 Windows 7 Pro 32-bit desktops at one of our sites, connected to a Windows 2012 AD. They have all started losing network connectivity (connectivity to our main site over a metro-e network, ...
0
votes
0
answers
187
views
Route part of a subnet to a different gateway
Data network is 10.220.0.0/20
DG is 10.220.1.19
I am trying to have all traffic in 10.220.8.0 - 10.220.15.255 (10.220.8.0/21) routed to this gateway: 10.220.1.251
I can't seem to accomplish this at ...
0
votes
1
answer
296
views
HP RIP on LAN Topology
We have 1 main core HP Routing Switch in server room that connects other data closet switches and 6 Data Closet switches that connect the clients.
We only have 3 VLANS. I have 2 questions:
1.) ...
0
votes
0
answers
187
views
Do you need STP on ProCurve trunks?
We have 3 switches - a Core Switch, and 2 downstream switches. Each downstream switch has a 3 cable Trunk direct to the core switch.
However - when we disconnected one cable in that trunk group (...