Questions tagged [route]
Command line tool for manipulating and listing the routing table.
617
questions
10
votes
3
answers
66k
views
Windows 7: Route single IP over different interface (wlan)
I am connected via Ethernet (10.1.1.1, interface 11) as well as via Wireless LAN (172.22.12.1, interface 12). I trying to route just a certain host (140.239.191.10 - which is whatismyipaddress.com for ...
5
votes
6
answers
43k
views
How to route based on domain name?
I can route by IP range by the route command. But is there any domain based route solution?
1
vote
3
answers
321
views
Network Configuration
This is my situation:
Router A: IP 192.168.1.1 Mask 192.168.1.0/24 - Connected to the internet.
Server:
- Interface eth0: inet addr:10.1.1.125 Mask:255.255.255.0 (connected to router B)
- ...
1
vote
2
answers
4k
views
How do I setup a router to forward packets (to/from) a specific IP to a specific _hardware port_?
I would like to route all traffic to 192.168.1.10 to hardware port 1 on my router and all traffic to 192.168.1.11 to hardware port 2 on my router. The issue here is that I have a network attached ...
2
votes
1
answer
970
views
Multicast routing
I got two firewalls running Keepalived and working ok.
I would like to pass the vrrp multicast traffic bethween a direct back to back link
between those firewalls (that direct link is already used by ...
1
vote
1
answer
3k
views
Windows VPN with different subnet
I just configured a Windows VPN server, this service will have a large number of clients, probably more than the LAN itself, I am thinking of using a different subnet on the VPN IP Pool, but not ...
-2
votes
1
answer
401
views
How to block inbound traffic from a host with 'route' in linux [closed]
I want to know if it's possible to block inbound traffic to a host but be able to send data only using 'route' command
Thanks :)
2
votes
3
answers
19k
views
OpenVPN working - but how to route all traffic down it?
I've setup a static one-to-one OpenVPN connection fine. However I can't seem to get the client to route all traffic via the VPN device. Here's my configs:
Client config:
remote 89.21.xx.xx
dev tun
...
3
votes
2
answers
11k
views
Using IP alias and route to visit a site through assigned IP address
I want to visit a site through assigned IP address.
I run the following commands:
ifconfig eth0:1 [ip address]
route add -host [the target host ip] dev eth0:1 gw [gateway]
This works fine on Ubuntu. ...
2
votes
5
answers
58k
views
solaris 10 route add on specific interface
I have 2 interfaces on Solaris box
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
hme0: flags=1000843&...
0
votes
2
answers
782
views
Route/IPtables Question
I have the following setup -
Verizon Fios Router - WAN - Public IP Address
Verizon Fios Router - LAN - 192.168.1.1
This connects directly to an internal Linux Router -
Internal Router Linux - eth0 -...
2
votes
3
answers
5k
views
OpenVPN Route traffic through Windows XP
I have installed an OpenVPN server + client, the server is windows xp and the client is slackware 12 linux. I set up the first tunnel, test it, ping the machines from each side and saw it's working.
...
0
votes
6
answers
11k
views
Network routing issues on Linux
I was hoping someone out there would be able to look at this and let me know what I have missed. I have 4 machines and for some reason, only 1 of them can talk to the other 3 via their private IP ...
0
votes
3
answers
1k
views
Poor-Man's Loopback on a Virtual Machine
I want to route the address 10.0.0.10 from my virtual machine back to my virtual machine through my physical router. How do I configure my virtual machine, host, and router to do so? The host is a 64-...
0
votes
3
answers
611
views
How can roaming user access same domain with varying IP address depending on location?
With my laptop, when accessing a given domain on the local network, I need to use a local IP address (192.168.x.x).
When accessing the same domain from a remote location, I need to use the public IP ...
5
votes
1
answer
6k
views
Default route is missing
I upgraded my server from Ubuntu 8.10 to 9.04 and now my default route is missing. So every time I boot I have to manually add it back with the command:
sudo route add default gw 192.168.10.1
How ...
20
votes
5
answers
16k
views
How to set up a VPN Incoming connection with Windows to tunnel Internet traffic?
I want to set up a VPN on a remote server to route all my Internet traffic for privacy reasons. I can set up an incoming connection and connect to it successfully. The problem is, I can just see the ...