Questions tagged [tp-link]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
2answers
169 views

How do I provide Internet Access to both of my VLANS?

I have a TP-LINK T1600G-28TS, and I have 2 different VLANS (10.0.0.0/24 ID 101 and 10.1.1.0/24 ID 102), their IP addresses are defined by the switch's DHCP server. This part is working fine, I can see ...
0
votes
0answers
109 views

How can I setup an OpenVPN server on OpenWRT, while maintaining interconnectivity between two routers and all attached nodes?

After wasting 7 hours of my life on How can I create two different subnets for 2.4 and 5GHz WiFi, and maintain communication between them?, and losing all confidence in myself as an IT professional, ...
0
votes
0answers
36 views

How Lan to Lan connection works over VPN?

Here is my Network structure The thing I want to do is to access 10.10.10.1 from the laptop on 4g internet with VPN connected. I can access 192.168.0.1 (tp-link router page) successfully over the VPN ...
0
votes
1answer
60 views

In a VPN, how to access resources inside a connected office from the VPN server

I have this Windows Server running on AWS, running a VPN with RRAS and NPS. The initial setup included only SSTP, and the users could easily connect from their Windows computers on their homes and use ...
1
vote
2answers
322 views

Basic 2 Routers configurations for noobs

So, my goal is to have each one of my devices connected to a double-NAT simple solutions. I've started my configuration with Router 1: IP: 192.168.1.254 Mask: 255.255.252.0 DHCP Ipv4: 192.168.1.10 -...
2
votes
2answers
4k views

Access computer on LAN behind OpenVPN server

I have a TP-Link VR400 Archer router on which I want to enable the OpenVPN server, so that a remote user can connect to the network and access a specific computer on the internal LAN. The router has ...
0
votes
1answer
709 views

Unable to connect to internal network through VPN

I am using two routers, one for connecting through VPN, and the other for internal network. My issue is after I connect via VPN, I can't access the internal network in other router. Here's my setup: ...
0
votes
1answer
958 views

Site to Site VPN devices behind ISP modem

site to site vpn setup when behind isp wifi router image I've read through many site to site vpn posts on this site but I still haven't found a solution to my issue. Here is the situation. I was ...
0
votes
2answers
641 views

Communicating between VLANS without routing - 802.1Q

I have a NVR which I can access on my LAN, I would like some IP cameras isolated on a VLAN to access the NVR using a 802.1Q managed switch only. I want the cameras to connect to the NVR without ...
2
votes
1answer
57 views

broadcast ping from wlan client - just 2 other clients respond? [closed]

The question came up when trying to integrate my KNX-IP interface via the java Calimero library. My implementation (running on the Raspberry - via WLAN) did not find the KNX IP interface, so I started ...
0
votes
0answers
2k views

Router (TP-Link MR200) with dynamic IP behind NAT failing to create IPSEC VPN to Ubuntu Strongswan

I've been trying to get this up and running and I got it further than I expected but am getting stuck at an error received INVALID_ID_INFORMATION error notify and there's a very peculiar local IP ...
2
votes
0answers
214 views

Router TP-Link TL-WDR4300 not Forwarding ports [closed]

Although I configured the forwarding ports in my router they are closed. I have a TP-Link TL-WDR4300 router connected to my home network. I also have a TP-Link TL-WA850RE repeater working as a Wi-Fi ...
0
votes
0answers
1k views

Cisco AnyConnect VPN Disconnects Internet with TP Link router

I use a TP Link Archer C20 Wirelss Dual Band Router to connect to fiber broadband service. For my office work, I connect to a VPN network, which works fine for sometime. And after a while, the VPN ...
1
vote
0answers
40 views

Bind WAN to TD-W8960N

I have a TD-W8960N DSL modem. It is possible to have multiple WAN services on the device as in Both of them are doing great as in Diagnostic How is it possible to bind two different computer to each ...
0
votes
1answer
116 views

Router Wi-Fi not working after power failure [closed]

I know this sounds lame, but it's the second consumer router in as many months which has Wi-Fi issues after power failures. My electric utility company sent notices this morning that they were working ...
0
votes
0answers
120 views

Access subnet from other subnet

We're running a FritzBox from our DSL-Provider in front of our TP-Link router. Now we want to use the DHCP-Server of the TP-Link, so all clients get a IP of the range 192.168.0.0/16. But we also want ...
0
votes
1answer
610 views

BT's 5 static IPs over PPPoE with TP Link Dual WAN TL-ER6020 router

Recently i bought nice dual WAN router TP Link TL-ER6020 to use it with two BT(British Telecom) Infinity Broadband lines with Openreach VDSL modems (Huawei HG612 , unlocked, as told Ebay seller). One ...
0
votes
2answers
224 views

WiFi AP Broadcasts DHCP Requests to all VLANs

My setup looks like this: Switch (T1600G-28TS) ------------------------------- | 1 | | | 6 | 5 | | ... | ------------------------------- | | | * ...
1
vote
1answer
94 views

Looking to mimic Netgear Nighthawk AC1900 Router Settings in a TP-Link MR3040 Router [closed]

I have a Netgear Nighthawk AC1900 Router that is setup and working correctly with a network that has two Wifi cameras and a Linux PC acting as a server. Static IP addresses have been assigned to both ...
0
votes
1answer
899 views

Using an LTE Dongle on a router's USB port

I know there are routers which support LTE/3G dongles (like the FRITZ!box by AVM). But if I have got a router, which officially does not suppport these dongles, but has got USB ports for NAT storage, ...
2
votes
2answers
2k views

Remote Management only via VPN on a TL-ER6020

We have a TL-ER6020 which we are setting up in a "Non NAT" mode (the WAN side is on a /30 network and routes a /29 network). I want to be able to "Remote Manage" the router, but want to prevent it ...
1
vote
0answers
729 views

Why don't TP-Link 24x-switches propagate clients when cascaded in two?

I'm behind two TP-Link switches those are cascaded behind a TP-Link router, which is in turn behind a consumer router that works as in modem only mode. Clients connected to the first switch work ...
-1
votes
1answer
2k views

Convert wifi to wired using wireless router [closed]

I have a TP-Link WR740N, a Raspberry Pi (With only an ethernet port for Network), and a Wifi connection. Is it possible to use the wireless router to bridge the Pi with the Wifi connection?
-1
votes
1answer
733 views

tp-link 1043nd no internet after flashing to gargoyle firmware [closed]

I have recently bought a tp-link wr1043nd version 1.10 and flashed gargoyle firmware 1.5.9 onto it after the intermediate step of flashing from stock firmware to German version of firmware. I have ...
0
votes
1answer
278 views

How to connect to a server via wifi device using a dialer(vpn)?

Question: How to connect to a server via Wifi device using a dialer? Description: I have a dialer that I use to connect to my cable network server in order to access the internet. I connect using ...
0
votes
1answer
1k views

TL-WR740N router or switch? [closed]

In this description page, it says that: The TL-WR740N is a combined wired/wireless network connection device integrated with internet-sharing router and 4-port switch. So, it's a router ...
0
votes
2answers
915 views

How to reset tp link router settings

I have changed the routers IP Address to 192.168.1.1 to 192.168.3.1. But now I cant access them both. What do I do?
0
votes
1answer
4k views

How to prevent router TP-LINK TD-8840T from disconnecting when idle?

I have the router TD-8840 from TP-LINK and it works well, but disconnects after some minutes it is idle. How can I disable that feature? I want that it will be connected allways.