Questions tagged [znapzend]
ZnapZend is an open source zfs send/receive backup tool with mbuffer and ssh support.
19
questions
3
votes
1
answer
578
views
How to define SSH port for target server with znapzendsetup
I have a firewalled server to send data to over ssh on public network, but the SSH port is not the default 22. How do I configure the port to znapzendzetup?
For mbuffer setting the port is not an ...
- 133
3
votes
2
answers
1k
views
How can I ratelimit znapzend?
I'm using znapzend to do some backups and unfortunately its flooding my gigE connection. I would like the ability to ratelimit znapsend. Something like:
zfs send | pv -L 200m | ssh $host zfs recv
...
- 31
2
votes
1
answer
2k
views
znapzend cannot receive new filesystem stream: dataset is busy
have 2 test system running last Nexenta 4.0.3-FP4community .Master and slave ,
mbuffer installed on both,ssh trust is ok between hosts
when running znapzend on master replication snapshot did not ...
- 41
2
votes
2
answers
980
views
How to monitor znapzend?
How one can monitor znapzend?
Yes, I am aware it produces logs, but logs are pretty extensive and reading them through when you are backing up many filesystems is not convenient at all.
Ideally: ...
- 46
1
vote
1
answer
1k
views
Time to run znapzend job
I have setup znapzend and have created the following job:
/opt/znapzend/bin/znapzendzetup create --recursive --mbuffer=/usr/bin/mbuffer --mbuffersize=1G \
> --tsformat='znapzend-%Y-%m-%d-%H%M%S' \
> ...
1
vote
2
answers
779
views
"Host key verification failed" on znapzendzetup create command
Just getting started with znapzend which compiled fine on Ubuntu 14.04 (the source machine, since updated to Ubuntu 16.04). Destination machine is Ubuntu 16.04 ('backupserver'). I've setup a non-...
- 21
1
vote
1
answer
393
views
znapzend not taking snapshots after the initial set up
I installed znapzend on unraid and did the initial configuration. My daemon is running but zfs list -t snapshot shows no datasets available
*** backup plan: citadel ***
enabled = on
...
- 21
1
vote
1
answer
368
views
Can znapzend be used for replication only?
Is there a recommended znapzend plan to specify when using znapzend for replication only?
I've been able to make it work by specifying a src and dst plan of ''1s=>15min' which essentially says do a ...
- 91
1
vote
1
answer
333
views
znapzendzetup create fails indicating it can't find SRC filesystem being created
Why does znapzendzetup create fail indicating it can't find SRC filesystem being created
sudo znapzendzetup create --tsformat='%Y-%m-%dT%H:%M:%SZ' SRC '1min=>10min,5min=>20min' /mnt/test/src ...
- 1,922
1
vote
0
answers
56
views
ERROR: zLog must be specified at creation time
I have a question, i simply want to make a lokal backup of my zfs filesystem.
This is the command i got:
znapzendzetup create --recursive --tsformat='%Y-%m-%d-%H%M%S' SRC data DST '1y=>1w' HDD
Now ...
- 11
1
vote
0
answers
351
views
znapzend no longer works after upgrade to Ubuntu Server 20.04.1
Ubuntu Server was upgraded from 18.04 LTS to 20.04.1 LTS and subsequently znapzend service fails to start with the reason being:
znapzend[3436]: ListUtil.c: loadable library and perl binaries are ...
- 11
1
vote
1
answer
195
views
how to setup Carton, to compile znapzend 0.20.0?
When compiling from source using:
# ./configure --prefix=/opt/znapzend-0.20.0
# make
# make install
I get this error:
! Couldn't find module or a distribution Carton
I can compile version 0.19.1 ...
- 11
1
vote
0
answers
324
views
Configure "znapzend" on centralized backup server
Any idea if I can configure/use znapzend in way to "pull"/zfs receive snapshots from servers that I want to backup?
I would like to have configuration where a backup server initiates backup process.
- 11
1
vote
0
answers
107
views
Multiple arguments in znapzendzetup --tsformat?
I was wondering if znapzendzetup --tsformat option can take multiple arguments? I.e. one per interval/retention period.
- 11
0
votes
1
answer
277
views
znapzend systemd service and command line arguments
I'm starting znapzend using the included systemd unit file and I'm wondering if there's any way, short of editing the unit file and changing the ExecStart command line, to specify runtime options for ...
- 91
0
votes
1
answer
174
views
Znapzend installation error
I am trying to install znapzend 0.15.7 in OmniOS R151014 but got the following error:
root@sgtestnas01:/opt# wget https://github.com/oetiker/znapzend/releases/download/v0.15.7/znapzend-0.15.7.tar.gz`
...
0
votes
1
answer
342
views
znapzend throwing up errors attempting to delete old snapshots
I am moving backup to znapzend. I see the following error on the backup server. However the backups are working fine and I can see the latest snapshots the backup server. The errors below pertain to ...
- 101
0
votes
1
answer
575
views
znapzend DST file system
I'm working with a new znapzend environment. The snapshots are happening, and I have just one destination, a remote server set up just to store the archived data. It appears the data stored on the DST ...
- 1
0
votes
1
answer
397
views
znapzend fails when running from cron
I'm having an issue with znapzend --runonce
I am running Debian Wheezy
I'm running from cron as I need to stagger my snapshots
I have the following in my crontab
PATH=/usr/local/sbin:/usr/local/bin:/...
