vigilem
  • Member for 6 years
  • Last seen more than 5 years ago
  • Northeast US
Show status of a Windows service from the command prompt
13 votes

You can use Powershell thus: Get-Service -name 'IIS Admin Service'

View answer
HP ProCurve 5412zl warm-boots on power failure while attached to UPS
Accepted answer
3 votes

My initial and immediate thoughts are along the lines of what you're contemplating. If these blips are occurring independent of any self-test schedules you have set up on the UPS (if the blips happen ...

View answer
How to check if promiscuous mode is enabled on network interface in windows server 2012 R2
Accepted answer
3 votes

Powershell. Get-NetAdapter | Format-List -Property PromiscuousMode That'll give you true or false.

View answer
Powershell: Save CSV result to folder
2 votes

You need to specify a filename at the end of your -Path variable, like this: C:\temp\scheduled_tasks_audit\audit.csv

View answer
HP ProCurve 2920, MAC filter
Accepted answer
2 votes

Port-security settings will accomplish this for you. I'd set it up to learn the MACs of your authorized devices and proceed from there. Instructions: http://whp-aus1.cold.extweb.hp.com/pub/...

View answer
HP Hard Drive ABC Slots
Accepted answer
2 votes

That's just the tray. If you still have the bad drive, take it out of the tray and put the new drive in the same tray (assuming that the drive itself is bad and not the tray, of course).

View answer
Apache2 after graceful restart needs 100% cpu
2 votes

https://issues.kolab.org/show_bug.cgi?id=5225 If you read down a bit, you'll see that Kolab doesn't support Debian's apache2. Might that be your issue? Symptoms sound similar.

View answer
Windows Server 2012 R2 Storage Spaces control panel icons disappeared?
1 votes

On Server 2012 R2, Storage Spaces is not administered via a Control Panel applet, but instead via Server Manager as you've pictured above. The Control Panel applet is visible on Win8/8.1/10 clients ...

View answer
Win10 unable to send Corporate (Windows) Error Report on internal network
1 votes

Have you made the requisite GPO change in Windows Components\Windows Error Reporting\Advanced Error Reporting Settings\Configure Corporate Windows Error Reporting - and have you made this change on ...

View answer
HAProxy: use_backend ignored because backend has no frontend capability
1 votes

You need to assign an ID number to the frontend (for example, ID 1). Then you need to assign said ID to the backend configs to match. So it would be like this on the frontend: frontend http: id 1 ...

View answer
Enable gateway only for authenticated clients
Accepted answer
1 votes

Perhaps a simpler method would be to use mac authentication in iptables and skip the whole separate website piece. Granted, this does not dynamically add a rule so it may not be to your liking, but it ...

View answer
May adding a route to a machine makes it reachable from the outside?
1 votes

The problem is likely not on server A. Since changing the switchports didn't give you any success, it's probably not the switchport - especially since with server B's original IP address you could ...

View answer
Let OS X ScreenSharing accept incoming connections only from a list of trusted IPs
1 votes

There are two mechanisms that accomplish this. One you've said you don't have presently and one you 'don't want to mess with'. You will have a difficult time accomplishing your goal given those ...

View answer
How does does a Dell MD12XX DAS appliance show up on a server
1 votes

The 1220s connect directly to the server's host-raid adapter - I believe the H800 is required for the 1200/1220. As far as benefit, the 1200 is slower, the 1220 is faster. If speed's your goal, 1220 - ...

View answer
IBM Domino - incoming e-mail loses formatting, no winmail.dat
Accepted answer
1 votes

If other external domains are sending email to you where winmail.dat is being processed successfully by Domino, then it's a sending-side issue. If this is the case, then a good test would be the ...

View answer
Increasing firewall throughput but constant traffic
1 votes

If traffic levels are the same but packet counts have increased (and these counters are accurate) then the simple answer is that your packet sizes have decreased on average over time, but this is not ...

View answer
Does RAM consumption use Network Bandwidth?
0 votes

Not directly, no. If you can get a packet capture on the network utilization during the calculation, you'll see what's using the bandwidth. Perhaps the server has to grab a bunch of data from a ...

View answer
Avaya switch - need to block port 25
0 votes

You'll do it via qos ACLs. I'd skip the web interface and do it on via CLI. See chapter 7.1 of the following: https://downloads.avaya.com/css/P8/documents/100123718

View answer
Setting up End-User Connection to ODBC Data Source
0 votes

If you set it up as a File DSN, you can then place said file on a network share and your teammates should be able to reference the file to import into Excel or whatever method they want to use to view ...

View answer
Save ODBC credentials for Oracle on Windows
0 votes

On your Windows server, set up the ODBC connection there. Administrative Tools>Data Sources (ODBC) I usually set these up under System DSN. Pretty straightforward - enter credentials/connection info/...

View answer
How to configure Fortigate 60D as L2PT/IPSEC client
0 votes

You can do this using the wizard or CLI on the Fortigate - configure it on the Fortigate side as a dialup VPN instead of site-to-site.

View answer
Setting up LAN at conference network
-1 votes

You could always run VirtualBox or Workstation and run one of the machines as a VM - unless your requirement is two separate physical machines.

View answer